Important Safety Instructions; Technical Specifications - Televes T.OX Série Guide Rapide

MUX DVBS2 - QAM/COFDM CI

Important safety instructions

General installation conditions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
11. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Inputs/Outputs/Connections description
The unit (Fig. 1) is provided with:
1.
IF satellite input
2. IF satellite input/output
3. RF input
4.
RF output
5. Module power supply input
6.
Status LED
7.
Control BUS connector
8. Slot CAM
9.
Programmer / PC connector

Technical specifications

Input frequency
DVB-S2
Symbol rate
DVB-S
Frequency steps
Satellite
demodulator
IN/OUT connectors
Input impedance
LNB powering
Satellite selection (DiSEqC)
Modulation format
Symbol rate
QAM modulator
(Ref. 564101)
Roll-off factor
Block code
Modulation format
OFDM
Guard interval
modulator
FEC
(Ref. 564201)
Bandwidth
Output frequency (selectable)
Frequency
steps
RF output
Max. output level
Attenuation (selectable)
Consumptions @ 24Vdc
(with signal)*
General
Protection level
* Consumptions are measured with input signal.
The consumption indicated for CAM and LNB are highest; in any case, depend on the type of CAM and LNB for each facility.
The technical specifications are defined for an ambient temperature of 45 ° C (113 ° F). For higher temperatures forced ventilation will be used.
MHz 950 - 2150
Mbaud
MHz
tipo
ohm
Vdc/KHz 13-17- OFF / 22KHz (ON-OFF)
Port
QAM 16, 32, 64, 128, 256
Mbaud
%
Reed Solomon (188, 204)
QPSK, 16QAM, 64QAM
1/4, 1/8, 1/16, 1/32
1/2, 2/3, 3/4, 5/6, 7/8
MHz
MHz
564101
KHz
564201 166 - 125 (selectable)
dBµV
dB
mA
IP
Warning
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as glasses, shall be placed on the apparatus.
Safe operation
Do not place the equipment near heat sources or in a highly humid environment.
Do not place the equipment in a place where it can suffer vibrations or shocks.
Please allow air circulation around the equipment.
Do not place naked flames, such as lighted candles on or near the product.
Symbology
Equipment designed for indoor use.
The equipment complies with the CE mark requirements.
Introduction
The multiplexor receives a satellite transponder in any of DVBS (QPSK) or
DVBS2 (QPSK or 8PSK) modulation formats, and demodulates it to obtain a
transport stream packet.
Then, the transport stream packet is modulated, either in QAM format (Ref.
564101) or COFDM format (564201), and converted to the output channel
by means of an agile up-converter.
Additionally, it incorporates a Common Interface slot for inserting a
conditional access module (CAM) that permits the unscrambling of
services.
To configure the multiplexer operating parameters (input frequency,
output channel, modulation format and adaptation of services mainly) can
be used the universal programming unit (ref. 7234) or the TSuite software.
Through losses (typ.)
10 -30
Modulation
2 - 42,5
1 FEC inner code
"F" female FEC outer code
75 Roll-off factor
Return losses (min.)
A, B, C, D
Scrambling
6,9 Interleaving
15 Bandwidth (max.)
Spectral inversion (selectable)
Scrambling
Interleaving
Cell_id
7, 8 Spectral inversion (selectable)
46 - 862 Through losses (typ.)
250
Return losses (typ.)
85 ±5 IN/OUT connectors
> 15 Output impedance
520 (LNB not powered/ CAM not inserted)
620 (LNB not powered/ CAM inserted)
870 (one LNB powered/ CAM inserted)
1120 (two LNB powered/ CAM inserted)
dB
DVB-S2 QPSK, 8PSK
DVB-S
LDPC 9/10, 8/9, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2
Bose-Chaudhuri-Hocquenghem
%
dB
DVB ET300429
DVB ET300429
MHz
Normal / Inverted
DVB ET300744
DVB ET300744
Selectable
Normal / Inverted
dB
dB
tipo
ohm
20
6
< 1,5
QPSK
20, 25, 35
10
8,3
< 1,5
> 10
"F" female
75