SAMES KREMLIN AZUR 72C160 Manuel D'utilisation page 238

DocuSign Envelope ID: DFD29580-C91F-4A36-AF7E-4D2B2F0CFF9B
The manufacturer herewith declares that the equipment is in conformity with the UK statutory requirements.
(1)
(2) Equipment type
Applicable
(3)
Directives
(9) Approved body
(10) This partly completed machinery must not be put into service until the final machinery in which it is
to be incorporated has been declared in conformity with Supply of Machinery (Safety) Regulations 2008.
SAMES KREMLIN is allowed to compil the technical documentation. SAMES KREMLIN undertakes to
transmit, in response to a reasoned request by the national authorities, relevant information on the partly
completed machinery in the most appropriate form. This declaration of incorporation of partly completed
machinery and this declaration of conformity are issued under the sole responsibility of the
manufacturer.
Director of the STAINS site - Executive Management (EM)
Hervé WALTER
Established in Stains, on
Siège Social / Headquarter: 13, chemin de Malacher - CS70086 - 38243 Meylan Cedex - France - Tél / Phone: +33 (0)4 76 41 60 60
(4) The relevant technical documentation was compiled as
The essential health and safety requirements mentioned in Supply of Machinery
2008 No.
(Safety) Regulations 2008 have been applied.
1597
Articles: 1.1 , 1.1.2 ,1.1.3, 1.1.5, 1.2, 1.2.2, 1.2.3, 1.2.4, 1.2.4.1 , 1.2.4.3, 1.2.6,
1.3, 1.3.1, 1.3.2, 1.3.3, 1.3.4, 1.3.6, 1.3.7, 1.3.9, 1.4, 1.4.1, 1.4.2, 1.4.2.1, 1.5,
1.5.2, 1.5.3, 1.5.4, 1.5.5, 1.5.6, 1.5.7, 1.5.8, 1.6, 1.6.1 , 1.6.2, 1.6.3, 1.6.4, 1.7,
1.7.1, 1.7.2
(5) That partly completed machinery is also in conformity with the provisions of
2016 No. 1107
(6) Marking
Designated
(7)
standards
(8) Conformity
assessment
procedure
Approved Body
21CLM 25031 - Ellesmere Port - United Kingdom / CML n°
10-févr.-23 | 18:05 CET
SAS au capital de 12.720.000 euros | RCS Grenoble: 572 051 688 | Code APE: 2829B | TVA intracom: FR36 572051688
DECLARATION OF INCORPORATION
OF PARTLY COMPLETED MACHINERY
UK DECLARATION OF CONFORMITY
POMPE AZUR™ 72C160
specified in annex VII, part B.
POMPE AZUR™ 72C160
II2G Ex h IIA T2-T4 Gb X
Ex h => Protection par sécurité deconstruction (c) /
Protection by constructional safety (c)
Conditions spéciales d'utilisation, le signe X indique de se
référer aux prescriptions figurant dans le manuel d'instructions
qui accompagent le produit.
Specific conditions of use, X indicates to refer to the
prescriptions specified in the instructions manual that
accompanies the product.
EN ISO 80079-36 : 2016
EN ISO 80079-37 : 2016
EN 1127-1 : 2019
Module A Technical documentation (Annex VIII)
Sames
1
DEC UK 578130130