Ninja NC302EU Notice D'utilisation page 3

27 DO NOT mix hot liquids. Doing so may
result in pressure buildup and steam
exposure that can pose a risk of the user
being burned.
28 DO NOT process dry ingredients
without adding liquid to the tub. It is not
intended for dry blending.
29 DO NOT use to grind ingredients.
30 NEVER operate the appliance without
lids in place. DO NOT attempt to defeat
the interlock mechanism. Ensure the
container and lid are properly installed
before operation.
31 Before operation, ensure all utensils are
removed from containers. Failure to
remove utensils can cause containers to
shatter and potentially result in personal
injury and property damage.
32 Keep hands and utensils out of
containers while mixing to reduce the
risk of severe personal injury or damage
to the unit. A scraper may be used ONLY
when the processor is not running.
33 DO NOT carry the unit by the handle
of the outer bowl. Hold the unit by
grasping both sides of the unit under
the head.
34 DO NOT process hard, loose ingredients
or ice. This appliance is not intended
to process loose frozen fruit, a block of
solid ice or ice cubes.
35 DO NOT freeze the tub at an angle. Tubs
must be placed on a level surface in the
freezer. Tubs frozen at an angle should
NOT be processed.
36 To avoid potential injury DO NOT misuse
the appliance.
Read and review instructions for operation and use.
Indicates the presence of a hazard that can cause personal injury, death or
substantial property damage
if the warning included with this symbol is ignored.
For indoor and household use only.
When using electrical appliances, basic safety precautions should always be
followed, including the following:
4
ninjakitchen.eu
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of
shock and unintended operation,
turn power off and unplug unit before
troubleshooting.
Unit moves on worktop while processing.
•
Make sure the worktop and feet of the
unit are clean and dry.
Frozen treat is liquid, not solid, after
processing.
•
If a base is soft after processing, put the
tub back in the freezer for several hours or
until desired consistency is reached.
•
For best results, freeze base for at least
24 hours and process immediately
after removing from the freezer. If the
processed base is still not firm, try setting
your freezer to a colder temperature. The
unit is designed to process bases between
-12°C and -25°C.
•
The proportion of fat or sugar may be
too high in your recipe. Consult the recipe
guide and use the recipes included as a
guide for best results.
Frozen treat looks crumbly or powdery
after processing.
•
When bases are frozen in very cold
freezers, they may come out crumbly.
After running the One-Touch Program, use
the RE-SPIN program to make your frozen
treat smoother and creamier.
•
The proportion of fat or sugar may be low
in your recipe. Consult the recipe guide
and use the recipes included as a guide
for best results.
One-Touch Programs will not illuminate.
•
Ensure the unit is plugged into a working
socket before installing the outer bowl.
Then press the power button to select a
program.
•
Make sure the unit is fully assembled for
use. If the unit is powered on and the outer
bowl is not installed correctly, the install
light will flash. If the paddle is not installed
correctly, the install light will illuminate. All
One-Touch Programs will illuminate when
the unit is fully assembled and powered on.
•
The unit does not allow you to run
programs back to back. Between
programs, lower the bowl and check the
results before raising the bowl and running
another program.
Install light is flashing.
•
The outer bowl is not installed or is not
installed correctly. Make sure to install the
paddle into the outer bowl lid and the lid
onto the outer bowl. Then place the outer
bowl onto the motor base with the handle
centred below the control panel. Twist the
handle to the right to raise the platform
and lock the bowl in place.
Install light is steadily illuminated.
•
The outer bowl is correctly installed,
but the paddle is missing or has been
incorrectly installed. Lower the platform
by pressing and holding the bowl release
button on the left of the motor base while
twisting the outer bowl handle toward the
centre. Be sure the paddle is installed in
the lid.
One progress bar light as well as all
program lights are flashing.
•
The motor has been overloaded and needs
to be reset. Unplug the unit, remove the
bowl and allow the motor base to cool for
approximately 15 minutes before running
again.
•
Remove the outer bowl lid and paddle.
Ensure no ingredients are jamming
the lid assembly.
•
The ingredients you are trying to process
might be too dense. Make sure you are
using ingredients with sugar or fat. Follow
the recipes in the recipe guide for best
results.
•
Your freezer might be very cold. The unit is
designed to process bases between -12°C
and -25°C. Change the setting of your
freezer, move the tub to the front of your
freezer or leave the tub out on the worktop
for a few minutes before processing.
•
DO NOT process a solid block of ice, ice
cubes, or hard, loose ingredients.
Middle two segments of the progress bar
are flashing.
•
There was an error and the program did
not successfully complete. Check that the
paddle is installed properly and try running
the program again.
ninjakitchen.eu 5