Gorenje S10/WHT953S1XBG Mode D'emploi page 22
After performing the maintenance, with the hood off and the button active, press the button for more than 3 seconds to perform the
reset of the lter saturation indicator; repeat the operation if necessary (for ex., when both lters are saturated).
Activationofthecharcoalltersaturationindicator
The saturation indicator of the charcoal lter is normally disabled. To activate it, proceed in the following manner:
With the display on (ON) and the suction off (OFF), press simultaneously the buttons
T9 lights on with steady light for approx. 5 seconds, to indicate the activation.
To disable it, repeat the operation; the button T9 will ash for approx. 5 seconds to indicate the disabling.
Buttons T8
and
T9
are not visible at this stage (on some models). They are visible only as described
in operation section of the manual.
Approximate distance of button
Setting of Automatic Operation parameters
For correct use of the automatic operation, perform „Hood Calibration".
Hood Calibration
With the display on (ON) and the suction off (OFF), press button
The suction speed (power) 2 starts functioning and button T3 ashes to indicate that hood calibration is initiated and it will last for approx.
15 minutes.
Note:
to interrupt the calibration, press
WHT943A2XBG, WHT643A2XBG, WHT663S2X, WHT963S2X
T1
T2
L1 L2 L3
To select the functions of the hood press on the symbol. Function will be activated when symbol will be released.
T1. Standby mode
(the control panel off – all functions disabled) /
Note:
After about a minute of inactivity (suction and lights), the hood will automatically switch to standby.
T2. ON/OFF lights
On certain models only (see drawing above):
press repeatedly to select the desired light intensity:
L1:
low light
L2:
medium light
L3:
high light
Press again to turn off the lights.
T3. ON/OFF Automatic operation "AdaptTech".
The hood automatically sets the suction speed (power)
require it.
If there are no variations in the environmental conditions, after 10 minutes (if the hood is already in suction speed (power) 1), the hood
turns off.
Note: for a correct use of this function, rst perform the „Setting of the parameters for Automatic Operation" (see corresponding
paragraph).
Note: During automatic operation, if the user acts on the other functions that adjust the speed, auto ventilation function is switched off.
T4. Manual selection of the suction speed (power):
L4:
suction speed (power) 1
L5:
suction speed (power) 2
L6:
suction speed (power) 3
Press again to turn off the hood (OFF).
Note:
manual selection excludes any other suction related set function.
T5. ON/OFF Intensive suction
Note:
After 5 minutes of operation the hood returns to its previous state.
T6*. (Only certain models ON/OFF intensive suction speed (power) "POWER BOOST x 2" (timed)
Note:
After 5 minutes of operation, the hood goes back to the previous status.
T7. ON/OFF operation mode „ReFresh".
Every 50 minutes of inactivity, the suction speed (power 1 is turned on for 10 minutes.
T8. ON/OFF Timer of the suction speed (power) (approx. 30 minutes)
Note:
this function is available for the speeds that can be selected with button
T9. Indicatorandresetltersaturation
The button lights on automatically with steady light when it is necessary to perform the grease lter maintenance.
The button lights on automatically with ashing light when it is necessary to perform the charcoal lter maintenance.
After performing the maintenance, with the hood off and the button active, press the button for more than 3 seconds to perform the
22 EN
T8
from
T7
is 15 mm, and distance of button
T3
for 5 seconds; the calibration will be invalidated and should therefore be repeated.
T3
T4
speed (power)
"POWER BOOST"
T9
from
T8
T3
for 3 seconds.
T5
L4 L5 L6
ON
(control panel switched on)
1
to increase if the environmental conditions detected by the hood sensor
(timed)
T4.
T8
and
T9
for more than 3 seconds; the button
T7
T8
is 40 mm.
15 mm
T6
T7
T9
40 mm
T8
T9
