Putting Into Operation; Accessories - Kaiser Fototechnik 5860 Mode D'emploi

ENGLISH
1. Scope of supply
5860 Lamp Holder
5861 Desktop Lighting Kit 1
5862 Desktop Lighting Kit 2*
3140 Studio Light
*also included in the Desktop Shooting Kits 5863 and 5864

2. Putting into operation

Do not connect the lamp holder (5) to the mains yet.
The lamp holder has to be mounted on a light stand (4) (Fig.
A) or a mounting system with a 16 mm standard spigot (3)
(light stand(s) are included with 5861-62). Loosen the locking
screw (6), fit the lamp holder and tighten the locking screw (6).
Attach the reflector (8) (supplied with 3140 and 5861-62) to
the lamp holder (5) (Fig. B).
Screw a suitable lamp (max. 250 W) into the ceramic socket
(9). See section 7 for suitable lamps.
Make sure that the mains voltage corresponds to the ope-
rating voltage given on the type plate (7) of the light. Then
connect the light to the mains.
The light is switched on/off with switch (1).
The light can be used for unlimited continuous operation.
3. Tilting and height adjusting
At first let the light (lamp holder, lamp, reflector (if fitted)) cool
down.
To tilt the light loosen the locking screw (6), move the light
into the required position (Fig. C) and tighten the screw again.
5861-62: To adjust the height of the stand, loosen the locking
screw (11) respectively (12) (Fig. D). Before doing so, hold up
the light to prevent it from moving downwards due to its own
weight. Tighten the locking screw again.
4. Diffusing cover and umbrella mount
The heat-resistant diffusing cover (13) (supplied with 3140
and 5861-62) can be used to achieve a softer illumination
(Fig. E).
A reflector umbrella or shoot-trough umbrella (Fig. F) can be
attached with the umbrella mount (2). The reflector (8) (sup-
plied with 3140 and 5861-62) has an opening (10) for the
umbrella rod allowing to attach an umbrella with a mounted
reflector. When attaching the reflector the opening (10) should
be on the bottom.
5. Important notes
Use the light with care, e.g. avoid wrong voltages or connec-
tion to equipment not specifically designed for this type of
light. Use lamps with max. 250 W. If these precautions are not
observed, the light may be damaged and in extreme cases
the lamp may burst.
Make sure that the light is not covered and keep away at least
0.5 m (20 in.) from heat-sensitive substances in direction of
light during operation.
Avoid touching the light (lamp holder, lamp, reflector) when
the light is on. Let the light cool down after use.
The light may only be serviced by qualified persons.
Lamp Reflector,
Holder ø 27 cm,
(10.6 in.)
1 x
1 x 1 x
2 x 2 x
1 x 1 x
Do not expose the mains cable to excessive physical
strain.
6. Maintenance and care
The light requires no maintenance. Make sure that the reflec-
tor (8) (with 3140, 5861-62) is free of marks and foreign bo-
dies. If necessary remove them before use. Clean the housing
of the light only with a soft dry cloth. On no account use pet-
rol or other cleaning agents and solvents.

7. Accessories

Suitable lamp for lamp holder 5860:
3128* Reflector lamp 150 W, 3200 K
Suitable lamps for lamp holder 5860 with attached reflector
(with or without diffusion cover):
3110
4356
3124
3130* Photoflood 250 W, 3000 K
3128* Reflector lamp 150 W, 3200 K
*not available in 120 V version
8. Specifications
Operating voltage: AC 230 – 240 V, 50 Hz or
Socket:
Lamps fitted
(per lamp holder):
Cable length:
Right reserved to make technical modifications.
Removable Desktop
diffusion cover stand
1 x 1 x
2 x 2 x
1 x
Energy saving lamp 25 W, 6400 K
Opal lamp 75 W, 3000 K
Opal lamp 150 W, 3000 K
AC 120 V, 60 Hz (see type plate)
E 27 (120 V: E 26)
250 W max.
approx. 3.80 m (12.5 ft.)
Energy saving lamp
25 W, 6400 K
1 x
2 x