Cardin Elettronica BL1924ASW Instructions D'utilisation page 19

Terminal board connections
7 CMN common for all inputs and outputs.
8 ELS electric lock output (fed continuously) 12 Vdc - 15 W.
9-10 LC-CH2 Potential free contact for the activation of the courtesy light
(separate power supply Vmax=30 Vac/dc: Imax=1A) or the second
11 CMN common for all inputs and outputs.
12 LP 24 Vdc 25 W output for warning lights.
intermittent activation (50%), 12,5 W continuous activation
13 LS 24 Vdc 3 W output for an indicator light.
14 CMN common for all inputs and outputs.
15 30 Vdc controlled output, powering external loads
16 CMN common for all inputs and outputs.
17 30 Vdc output, powering external loads
18 CMN common for all inputs and outputs.
19 TA (NO contact) opening button input
20 TC (NO contact) closing button input
21 TAL (NO contact) limited opening button input
22 TD (NO contact) dynamic button input
23 CMN common for all inputs and outputs.
24 TB (NC contact) stop button input (The opening of this contact inter-
rupts the cycle until a new movement command is given).
25 FTCS (NC contact) The opening of this contact will block all movement,
until the obstruction has been removed and the pause time has elapsed,
due to the safety device cutting in, the door will then continue moving
in the closing direction (only with automatic reclosing enabled).
26 FTCI (NC contact) safety and control devices in input (photocells invert
the travel direction when an obstruction is detected). Opening this
contact will provoke a travel direction inversion during closure due to
the cutting in of the safety device.
27 EMRG2 (NO) emergency manoeuvre input 2
28 EMRG1 (NO) emergency manoeuvre input 1
29 CMN common for the emergency buttons
30 Inner conductor for radio receiver antenna (if an external antenna is
fitted use a coaxial type cable RG58 with an impedance of 50 ).
31 Outer conductor for radio receiver antenna
10
J1
F3
L3
J2
10
Collegamento motori/encoder a 4 fili
Connecting motor/4-wire encoder
Branchement moteur/encodeur à 4 fils
Anschluss der Motor/Encoder mit 4 Drähten
Conexionado motores/encoder de 4 conductores
COLORE
CABLAGGI
Bl Blu
Gr Verde
Gy Grigio
Yw Giallo
KABELFARBEN
Bl Blau
Gr Grün
Gy Grau
Yw Gelb
ENCODER 1
M1
Bl Gr
1 2 3 4
B1 via radio
CSER Serial connection (only for diagnostics)
D1 Six-segment LED display
DS1 Selection dip-switch
F1 10A blade fuse (5) (motor power protection)
F2 10A blade fuse (5) (motor protection during battery operation)
F3 4A blade fuse (5) (24V circuit protection)
F4 4A blade fuse (5) (24V circuit protection during battery operation)
F5 4A blade fuse (5) (electric lock protection)
J1 Battery connection
J5
(1) .
(1) .
4A
F2 F4
L2
L1
F1
COLOUR CODE COLORATION
CODE DES CÂBLAGES
Blue Bleu
Green Vert
Grey Gris
Yellow Jaune
COLORACIÓN
CABLEADOS
Azul
Verde
Gris
F5
Amarillo
M2 ENCODER 2
Gy Yw Bl Gr Gy Yw
5 6 1 2 3 4 5 6
(1)
Note The total of the 2 external device outputs must not exceed 10 W.
ALL UNUSED NC CONTACTS MUST BE JUMPED and consequently the
security device test must also be deactivated (FTCI , FTCS - Dip 7 and Dip
OFF
and receiver parts of the security devices must be connected to the binding
CTRL 30 Vdc
delay between the command transmission and movement of the gate/s.
Switch on the power and make sure that the indicator LEDs are in the fol-
lowing condition.
- L1 Power on
- L2 Battery charging
- L3 Wrong battery connection
- L4 Transmitter code programming indicator
- L5
- L6
- L7
- L8
- L9
- L10
- L11
Note :
(2)
Note :
(3)
Note : Check that the activation of the safety devices switches the cor-
(4)
responding LEDs off.
If the green power on LED "L1" doesn't light up check the condition of the
fuses and the power cable connection at the transformer primary.
If one or more of the safety LEDs do not light up check the contacts of the
relative security devices and check that the unused safety device contacts
have been bridged.
R1
MM
L5
J3 J4
L6
L7
DS1
P2
TD
RA
L4
PLP
LP
LS
P3
FTCI
TFTI
TFTS
SAP
ELS
LC/CH2
7 8 9 10 11 12 13 14 15 16
J2 Transformer secondary protection
J3 Enable transmitter memorisation via radio
J4 Radio channel selection
J5 Binding posts 9, 10 selection (courtesy light/CH2 via radio)
MM Transmitter code memory module
P1 Programming button (PROG)
P2 Transmitter code memorization button (MEMO)
P3 Transmitter code cancellation button (DEL)
R1 Radio frequency module, 433 MHz for S449 transmitters
Note (5) : These are automotive type blade fuses (max. voltage 58 V)
19
FTCI, FTCS test both the transmission
TB
FTCS
TA
TC
TAL
TD/CH1
ON
ON
CS 1218 DC0355
B1
L8 L10
D1
L9 L11
CSER
J5
1 2
1 2
3
3
Pos.1 Pos.2
CMN
EMRG 1
EMRG 2
17 18 19 20 21 22 23 24 25
ON
OFF (2)
OFF (3)
OFF
ON (4)
(4)
FTCI ON
(4)
ON
OFF
OFF
OFF
OFF
P1
26