General Safety Instructions - Kreg PRS1015 Guide D'utilisation

WARNING When using electric tools, always follow the safety precautions below to reduce risk of fire, electric shock, and personal injury. Read
all these instructions before attempting to operate this product. SAVE THESE INSTRUCTIONS.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Don't use power tools in a dangerous environment. Don't use power tools in
damp or wet locations, or expose them to rain.
c) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks that can ignite the
fumes or dust.
d) Keep children and bystanders away while operating a power tool. Distractions c
an cause you to lose control.
e) Make your workshop child proof. Use padlocks, master switches, or remove
starter keys.
2) Electrical safety
a) Ground electric tools. If the tool is equipped with a three-prong plug, it must
be plugged into a grounded three-hole electrical outlet. If the proper outlet is not
available, have one installed by a qualified electrician. Never remove the third prong or
modify the provided plug in any way.
b) Do not expose power tools to rain or wet conditions. Water entering a power tool
increases the risk of electric shock.
c) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
d) Use a proper extension cord and make sure it is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current your
power tool draws. An undersized cord causes a drop in line voltage resulting in loss of
power and overheating. Table 1 on the following page shows the correct cord gauge to
use depending on cord length and tool nameplate ampere rating. If in doubt, use the
next heavier gage. The smaller the gauge number, the heavier the cord.
e) When operating electric tools, avoid body contact with grounded or earthed
surfaces such as pipes, radiators, kitchen ranges, and refrigerators. Contact with a
grounded surface increases the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power tools
can result in serious personal injury.
b) Always wear safety glasses. Everyday eyeglasses are not safety glasses. Safety
glasses have specially constructed lenses, frames, and side shields.
c) Use safety equipment. Use a face or dust mask when the cutting operation is
dusty. Safety equipment such as a dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions reduces personal injuries.
d) Avoid accidental starting. Make sure the switch is in the off-position before
plugging in. Carrying power tools with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
e) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool can result in personal
injury.
f) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
g) Secure workpieces. Use clamps or a vise to hold work when practical. This is safer
than using your hand and it frees both hands to operate the tool.
h) Never stand on the machine. Serious injury can occur if the tool tips or if the cutting
tool is unintentionally contacted.
i) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts. Roll up long sleeves to the elbow. Wear protective hair covering
to contain long hair.
j) If devices are provided for the connection of dust extraction and collection
equipment, ensure these are connected and properly used. Use of these devices
reduces dust-related hazards.
4) Power tool use and care

General Safety Instructions

a) Keep guards in place and in working order.
b) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
c) Use the right tool. Don't force a tool or attachment to do a job for which it was not
designed.
d) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
e) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
f) Never leave a tool running unattended. Turn power off. Don't leave the tool until it
comes to a complete stop.
g) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool and these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
h) Maintain power tools. Check for misalignment or binding of moving parts,
broken parts, and any other condition that can affect power tool operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
i) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
j) Use the recommended speed for the cutting tool or accessory and workpiece
material.
k) Only use parts and accessories recommended by the manufacturer. Consult
the owner's manual for recommended accessories. Using improper accessories can
cause personal injury.
l) Use the power tool, accessories, and tool bits in accordance with these
instructions and in the manner intended for the particular type of power tool,
taking into account the working conditions and the work to be performed. Use
of the power tool for operations different from those intended can result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This ensures that the safety of the power tool is maintained.
6) Safety instructions specific to using a router table fitted with the
Precision Router Table Fence
a) Read, understand, and follow your router manufacturer's safety warnings
and instructions.
b) Disconnect the router from power before making adjustments. Never adjust
the fence, plate, reducing rings, or any part of the router or router table while the
router is running.
c) Place the router table on a flat surface to prevent tipping or sliding. Never
stand on the router table.
d) Do not attempt to rout warped, twisted, or bowed workpieces. All
workpieces must have flat faces and square edges.
e) Do not attempt to rout very large workpieces on a router table. Very large
workpieces can be difficult to control and can cause the router table to tip over.
f) Only use router bits in your router. Never use tools such as carving burrs,
mounted abrasives, wire wheels, or drill pits, even if the shanks match the
diameter of the router collet.
g) Wear gloves when handling router bits. Cutting edges are sharp.
h) Never use dirty, dull, or damaged router bits. Remove wood-resin build-up
with a cleaner specifically formulated for cutting tools. Have dull bits sharpened by
a qualified person. Discard damaged bits.
i) Make sure at least 75% of the router-bit shank length is securely held in the
router collet. To ensure a secure hold, leave
the end of the bit shanks and the bottom of the collet.
j) Use the insert-plate reducing ring with the smallest opening that allows the
bit to pass through it. A large gap around the bit can allow the workpiece to tip
⁄ " to ⁄ " (2mm-3mm) between
1 1
16 8