Music Player; Replay From The Usb Port; Replay From The Computer - IMG STAGELINE WAP-200 Mode D'emploi

FM
Scan setting
Audio setting
System settings
Main menu
The line Scan setting
lected . Press the knob CONTROL SELECT .
The following confirmation prompt will
appear:
FM station scan
Strong stations only?
YES*
Turn the knob CONTROL SELECT to select
the setting and then press the knob
NO
to confirm .
8) Prior to scanning for the next station, first
wait for the display to indicate the station
most recently set .
Forward scan:
At the unit, press the knob CONTROL
SELECT .
Note: If the reverse scan starts, briefly turn
the knob to the right in order to change the
scan direction .
On the remote control, keep the button
  I pressed until the scan starts .
Reverse scan:
At the unit, briefly turn the knob CON-
TROL SELECT to the left (to change the
scan direction) and then press the knob .
On the remote control, keep the button
I   pressed until the scan starts .
9) Store the station as described in step 5 .
Proceed in the same way to scan and store
the other stations .
10) Stations with poor reception may be dis-
turbed by noise . To reduce the noise, set
the reproduction to mono: Press the but-
ton MENU . The menu "FM" will appear
(fig . 37) . Select the line
and confirm . The following confir-
ting
mation prompt will appear:
FM weak reception
Listen in Mono only?
YES
Turn the knob CONTROL SELECT to select
the setting and then press the knob
YES
to confirm .
Note: All stations will then be reproduced in
mono . For stereo reproduction of stations with
strong reception, set
NO
reception" again .
20

4.4 Music player

The music player is able to replay audio files
in the formats MP3, AAC, WMA, WAVE or
>
FLAC from a USB flash drive, a hard disk or a
>
computer in the local network .
Fig. 37
will be se-
NO
Fig. 38

4.4.1 Replay from the USB port

1) Insert a USB flash drive into the USB port
2) Once the data storage device has been
Audio set-
NO*
Fig. 39
3) To select a different track, turn the knob
4) For information on how to create and re-
in the menu "FM weak
Press the button MODE repeatedly
until appears . Then,
Music player
the menu "Music player" will appear:
Music player
Shared media >
USB playback
My playlist >
Repeat play: Off
Shuffle play: Off
or connect a hard disk to the port .
After a short time, the following message
will appear:
USB playback
USB disk attached -
Open folder?
YES NO
will be selected . To indicate the tracks
YES
stored on the data storage device, press
the knob CONTROL SELECT .
If the message shown in fig . 41 does not
appear, turn the knob CONTROL SELECT
in the menu "Music player" to select the
line and then press the
USB playback
knob to confirm .
opened, its contents will be shown:
USB play back
Blues >
Country >
POP >
Beat Machine - Come...
DoMan - Go!
Turn the knob CONTROL SELECT to select
a track (if applicable, also from a folder,
indicated by > ) and then press the knob
to start the replay .
Music player
10:43PM
0:26 3:12
USB
CONTROL SELECT . To exit a folder selected,
press the button BACK .
play a playlist, see chapter 4 .4 .4 .

4.4.2 Replay from the computer

The WAP-200 and the computer must be con-
nected to the same local network . A UPnP
service (Universal Plug and Play), e . g . Win-
dows Media Player (version 10 or later), must
be installed on the computer .
Windows is a registered trademark of Microsoft Corpora-
tion in the United States and other countries.
1) Switch on the music replay mode so that
the computer can recognise the WAP-200 .
2) Set the computer in such a way that it
works as a media server; for Windows 7,
for example, proceed as follows:
Fig. 40
A – Network settings
 Start
 Control Panel
 Network and Internet
 Network and Sharing Center
 Change advanced sharing settings (left
column)
 Click after "Home or Work" .
 Under "Media Streaming", click
"Choose media streaming options ..." .
Fig. 41
 If media streaming has not been
turned on yet, an activation window
will appear: Click the button "Turn on
media streaming" . (This window will
be skipped when streaming has been
turned on .)
 For "Show Devices on", select the op-
tion "All Networks" .
 After "Media programs on this PC and re-
mote connections", click "Customize ..." .
 Tick the option "Use default settings"
and click "OK" to confirm .
 After "Media programs on this PC and
remote connections" and "Customize",
select the setting "Allowed" .
 Click "OK" to exit the media streaming
Fig. 42
options .
 In the sharing setting options, click
again after "Home or Work" .
 Under "Network Discovery", select the
setting "Turn on network discovery" .
 Click "Save All Changes" .
 Close the window "Network and Shar-
ing Center" .
Notes:
Fig. 43 1 . The settings can also be made via the Windows
Media Player (menu "Stream") .
2 . If applicable, make changes to the Firewall
settings .