IMG STAGELINE WAP-200 Mode D'emploi page 16

The other options are:
Automatic setting via a DAB station or an
FM station or manual setting (no update) .
Note: An automatic setting will only be made
when a corresponding station is received . There-
fore, select the setting that corresponds to the
operating mode most frequently used: If you lis-
ten to the digital radio for most of the time, for
example, select
Update from DAB
mainly use the Internet to listen to the radio, leave
the setting
Update from NET
Select the setting with the knob CONTROL
SELECT and then press the knob to con-
firm .
5) The following menu displayed depends
on the selected setting; additional time
settings may be required:

Update from DAB
No additional time settings are required
(including daylight saving time change) .
Continue with step 6 . The menu shown
there (fig . 11) will appear .

Update from Network
The menu "Set timezone" will appear:
Set timezone
UTC +00:00: Dublin, L.*
UTC +00:30:
UTC +01:00: Madrid, A. ..
UTC +01:30:
UTC +02:00: Athen,Cai...
For Great Britain, the correct setting has
been selected:
UTC +00:00: Dublin, London
Press the knob CONTROL SELECT to con-
firm this setting or, for a different country,
first select the appropriate time zone and
then confirm your selection . The menu
"Daylight savings" will appear:
Daylight savings
Daylight savings
ON OFF*
During the winter time, leave the setting
unchanged; for the summer time,
OFF
select the setting
ON
TROL SELECT . Press the knob to confirm
the setting . Continue with step 6 . The
menu shown there (fig . 11) will appear .

no Update
The menu for the manual time setting will
appear:
Set Time/Date
01-01-2007
12:00 AM
The digits for the day will flash . Turn the
knob CONTROL SELECT to set the day and
then press the knob to confirm . The digits
for the month will start flashing . Proceed in
the same way to set the month, the year,
the hours, the minutes and, if required,
AM or PM . To return to the previous set-
ting, press the button BACK .
6) When the final time setting has been con-
firmed, the following message will briefly
appear:
16
Then a country list for the network setting
will appear:
, or if you
unchanged .
Most of Europe
USA
Canada
Spain
France
7) The line
For Great Britain, press the knob CONTROL
SELECT to confirm this setting . The unit
or
FM
will search for a network:
Network settings
Then the menu with the networks found
will appear:
[Rescan]
Fig. 8
[Wired]
[Manual config]
A To establish the connection to
B If the name of your router is shown in
Fig. 9
with the knob CON-
C If the name is not shown and if the
Fig. 10
D If the name is not shown and if a wire-
? Please select
Wlan region
Fig. 11
Wlan region
Fig. 12
is selected .
Most of Europe
Network wizard
Scanning/
Fig. 13
SSID
Fig. 14
the network later (otherwise con-
tinue with item B, C or D):
Press the button MENU; answer the
question Run wizard again at
next start up? with
WAP-200 can now be used (chapter 4
on page 18), however, not as an In-
ternet radio .
this menu:
Turn the knob CONTROL SELECT to
select the name and then press the
knob to confirm . If the network access
is not encoded, the connection to the
network will be established; continue
with step 10 . If the access is encoded,
continue with step 8 .
WAP-200 is connected to the router
via a cable:
Use the knob CONTROL SELECT to se-
lect the line [Wired] and then press
the knob to confirm . If the network
access is not encoded, the connection
to the network will be established;
continue with step 10 . If the access is
encoded, continue with step 8 .
less connection shall be made to the
router:
a) Use the knob CONTROL SELECT to
select the line
[Manual config]
and then press the knob to confirm .
b) In the following menu, select
and confirm .
Wireless
c) In the following menu, select the
line
DHCP enable
if the router automatically transfers
the network settings to the WAP-
200 via DHCP (Dynamic Host Con-
figuration Protocol) .
If the DHCP function at the router is
deactivated or not available, select
the line
firm and make the network settings
manually in the following submenus;
then continue with step d .
d) The menu for entering the network
name will appear:
SSID
0123456789._- ,
abcdefghijklmn
opqrstuvwxyzABC
DEFGHIJKLMNOPQR
Fig. 15
Turn the knob CONTROL SELECT to
select the first character and then
press the knob to confirm . Proceed
in the same way to enter the other
characters . Then select the field
(to be found between the special
characters and the digits) and press
the knob .
= delete last character
BKSP
CANCEL
e) The menu "Authentication" will
appear:
Authentication
Open
Pre-Shared Key
WPA
NO . The
WPA2
Fig. 16
In most cases, the setting
(Wi-Fi Protected Access 2) must be
selected for newer routers .
f) The menu "Encryption type" will
appear:
Encryption type 8/9
TKIP
AES
Fig. 17
For most routers, the setting
(Temporal Key Integrity Protocol)
must be selected .
8) If the network access is encoded, a menu
for entering the password will appear (for
a WPS-encoded network, continue with
step 9) .
Key:
0123456789._- ,
abcdefghijklmn
opqrstuvwxyzABC
DEFGHIJKLMNOPQR
Turn the knob CONTROL SELECT to select
the first character and then press the knob
to confirm . Proceed in the same way to
enter the other characters .
and confirm
DHCP disable , con-
BKSP
OK
CANCEL
OK
= return to the previous
menu
7/9
>
>
>
>
WPA2
TKIP
BKSP
OK
CANCEL
Fig. 18