MasterFlow AH-301 Mode D'emploi page 2

Description & Introduction
The Masterflow Heat Blower
®
is a heavy-duty, industrial quality
heat blower suitable for continuous
duty applications. It produces a high
volume of hot air for demanding
industrial applications. The adjustable
stand features a keyhole slot for easy
equipment mounting and allows
the nozzle capability of rotating 90°
(horizontal to vertical).
Specifications
Model
AH-301
AH-302
AH-501
AH-502
AH-751
AH-752
*Average temperature measures 1" from nozzle.
Important Safety Instructions
WARNING: THIS PRODUCT
IS A SOURCE OF VERY HIGH
TEMPERATURE FLAMELESS
HEAT. AS WITH ANY ELEC-
TRICAL TOOL, WHEN USING
HEAT TOOLS, ALWAYS FOLLOW
BASIC SAFETY PRECAUTIONS,
INCLUDING THE FOLLOWING,
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR PERSON-
AL INJURY.
1) Read and understand this
instruction manual before using.
Save this manual for future
reference.
WARNING: To reduce the risk
of fire or electric shock, do not
expose heat blowers to rain or
moisture. Store indoors. Con-
nect to grounded outlet only.
2) Do not use plug adaptors or re-
move the ground prong from the
plug. This tool is equipped with
a 3-prong plug and a 3-wire
grounding system. Connect to
properly grounded outlets only.
3) Use heat blower only on
adequately rated circuits to
avoid overheating of electrical
systems.
4) Masterflow Heat Blowers can
produce up to 750°F/400°C of
flameless heat out of the nozzle.
Do not direct this hot air stream
at your clothing, hands or body
parts. Do not use as a hair
dryer.
5) Do not touch nozzle opening or
nozzle shield until cool. When
in "Hot" mode, extreme heat
is generated at those areas.
Always hold tool by the handle
or use permanently attached
stand.
2
Your Masterflow
a thermal fuse which will protect
the element from over heating or
burn out due to a nozzle blockage
or motor failure.
Heat blowers are a source of ex-
tremely high temperature flame-
less heat (up to 750°F/400°C).
As with other products which
*Temperature
°F °C
300 150
300 150
500 260
500 260
750 400
750 400
6) Run on "Cold" before turning
off. The nozzle and shield
require approximately 3 minutes
to become cool to the touch.
7) Do not touch work surface with
nozzle. Keep nozzle face at
least 1" away.
8) Keep a clean work area. Messy
or cluttered work areas invite
accidents or injury.
9) Keep away from children or
persons with reduced physical,
sensory or mental capabilities,
or lack of experience and
knowledge. All visitors should
be kept at a safe distance from
the work area. Do not let visitors
touch the tool or extension cord.
10) Use tool in a well-ventilated
area. Do not use near flamma-
ble liquids or in an explosive
environment (where fumes,
gases or dust are present).
11) Remove all highly flammable
materials and other debris from
the work area.
12) Wear safety glasses at all
times.
13) When using an extension cord,
use only a 3-wire grounded cord
with a minimum of 14-gauge
capacity. We recommend they
be listed by Underwriters labora-
tories (UL) in the U.S.A. or (CSA)
Canadian Standards Association
in Canada and be suitable for
outdoor use. Cords marked for
outdoor use are also suitable for
indoor use.
14) Don't abuse cordset. Never
yank by cord to remove from
is equipped with
generate extremely high tem-
®
peratures, regardless of your
specific application, extreme
care and caution should be ob-
served when using this product.
Therefore, we recommend that
you pay particular attention to
the safety instructions which
we have provided for your
protection.
Volts
120
220/240
120
220/240
120
220/240
electrical outlet or carry tool by
cord.
15) Don't remove adjustable stand.
When not hand-held, place
tool on a level surface. Position
cordset so it does not cause
tipping.
16) Keep a fully-charged fire extin-
guisher close at hand.
17) Do not leave heat blower unat-
tended while the heat blower is
running or cooling down.
18) Stay alert. Do not operate tool
when you are tired. Use com-
mon sense and watch what you
are doing.
19) Store properly. Do not store
while hot. Store in a dry, high or
locked-up location. Keep out of
the reach of children.
20) WARNING: This product, when
used for soldering and similar
applications, can expose you
to LEAD, which is known to
the State of California to cause
cancer and birth defects and
other reproductive harm. For
more information go to
www.P65Warnings.ca.gov
READ THESE INSTRUCTIONS
WARNING: Hidden areas such as
walls, ceilings, floors, soffit boards
and other panels may contain
flammable liquids that could be
ignited by the hot air gun when
working in these locations. The
ignition of these materials may
not be apparent and could result
in property damage and injury to
persons. Do not use if in doubt
Amps
10.0
5.0
14.0
7.2
18.0
9.4
IMPORTANT SAFETY
INSTRUCTIONS
www.masterappliance.com