Milwaukee 0780-20 Manuel De L'utilisateur page 3

Symbology
Underwriters Laboratories, Inc.,
United States and Canada
Specifi cations
For use with
Cat. No. Volts Capacity
Battery Packs:
0780-20 28 DC 2 Gal. 48-11-2830 V28™
(7.5 L)
0880-20 18 DC 48-11-1830 V18™
2 Gal.
48-11-2230 18 V NiCd
(7.5 L)
48-11-1815 18 V Li-Ion
FUNCTIONAL DESCRIPTION
1. Carrying handle
2. Battery compartment latches
3. Motor housing
4. Tank
5. Tank latches (front and back)
9
6. Intake port
7
8
6
11
Direct Current
Battery packs for use
with chargers:
48-59-2818, 48-59-0280
48-59-2818, 48-59-0280
48-59-2818, 48-59-0255, 48-59-0186,
48-59-0260, 48-59-0280
48-59-1801
1
2 2
7
5
4
10
7. Accessory storage
8. Battery bay
9. Switch
10. Blower port
11. Hose storage
4
Always remove battery pack before
changing or removing accessories.
Only use accessories specifi cally
recommended for this tool. Others
may be hazardous.
Installing/Removing Battery Pack
1. Lift and release battery compartment
latches and open battery compartment.
2. To remove the battery pack, pull it off of
the bay.
3. To insert the battery pack, slide it into
the battery bay.
NOTE: The 18 V Vacuum has 2 bays
available. Use the left side bay for
48-11-1830 V18™ and 48-11-2230 18 V
NiCd battery packs. Use the right side
bay for 48-11-1815 18 V Li-ion battery
packs.
3
Fig. 1
4. Close battery compartment and secure
both latches.
To reduce the risk of injury, always
remove the battery pack before
releasing the tank latches.
Installing/Removing the Filter
Use the cartridge filter for dry and wet
pickup.
1. Remove the battery pack. Close and
latch the battery compartment.
2. Release the tank latches and lift off the
motor housing. Place it upside down on
a fl at surface.
ASSEMBLY
WARNING
3. To remove the fi lter, turn it 1/2" counter
clockwise and pull it off of the motor
housing/fl oat cage.
4. Empty all debris from the tank.
5. To clean the filter, shake off excess
dirt or rinse the outside with water. Dry
completely.
6. To install the fi lter, slide it over the fl oat
cage. Line up the fi lter tabs with the
motor housing notches and turn it 1/2"
clockwise to lock in place.
7. Replace the motor housing and secure
both latches.
Keep fi lters clean. Effi ciency of the
vacuum is largely dependent on
the fi lters. Dirty fi lters will reduce
the air fl ow and effi ciency of the
fi ltration system. Do NOT machine
wash or dry.
To reduce the risk of injury, wear
safety goggles or glasses with side
shields and dust mask when using
the vacuum as a blower. Clean tank
completely before use.
Pickup/Blower
The vacuum can be used for debris pickup or
WARNING
as a blower, depending on the port used.
1. For debris pickup, insert the large end
of hose into the intake port of the motor
housing, lining up the tabs on the hose
with the notches in the port. Twist to
secure and form a tight fi t.
2. To use as a blower, insert the large end
of hose into the blower port
motor housing, lining up the tabs on the
hose with the notches in the port. Twist
to secure and form a tight fi t.
3. Attach one of the accessories to the other
end of the hose. Twist to form a tight fi t.
Use 1-1/4" opening accessories.
5
CAUTION
WARNING
of the