Télécharger Imprimer la page

Extreme Max 5600.3154 Instructions D'installation

Les langues disponibles

Les langues disponibles

Liens rapides

-naäuC7$
Warning:
Risk of personal injury or property
in a sudden
release
of the
winch
instructions
and install
and maintain
winch manufacturer's
instructions
Includes:
(1)
Winch
Mount
(A)
(2)
M6-1.00
x 25mm
x 38mm
(4)
M6 Nylock Nut (C)
(4)
M6 Flat Washer
(D)
(2)
M8-1.25
x 25mm
HH Bolt (E)
Prior
to Installation:
I. Turn
off
vehicle.
2. Locate the battery
compartment.
hood,
however,
the battery
seat of the 2014 Ranger 800 4x4, and under the rear driver-side
the 2014 Ranger 800 Crew.)
3. Remove
the ground
terminal,
the battery
cables.
Remove the LH plastic radiator
I) Remove plastic rivets. (See Figure 1.1)
2) Release the plastic tabs (1.2) on both sides to remove the radiator
screen.
3) Remove
shroud
and screen.
Remove the two (2) middle bumper
bumper
to the middle of the ATV frame.
Position the mounting
plate on the front bumper.
Install (2) U-Bolts,
(4) washers,
plate to the ATV frame.
Do not tighten
Attach
fairlead
to the fairlead
your winch or fairlead.
Mount winch to mounting
your
winch.
Note:
You may need to trim
accommodate
some
Use the supplied
8mm
bolts
mounting
location.
(See Figure 2.1) Do not tighten
When
all hardware
is installed,
recommended
torques:
6mm
Bolts
-12 N-m (9 ft-lb)
8mm
Bolts -37 N-m (27 ft-lb)
6mm
U-Bolts
-10 N-m (7ft-lb)
Note: Follow all winch instructions
Re-install
shroud
and screen.
Customer Service: service@extrememax.com
Winch
damage. An improperly
mount
and/or
winch
hardware
at recommended
for proper mounting
U-Bolt
(B)
(In most models this will be under the
compartment
is located
then the positive
terminal
shroud and screen. (See Figure 1.)
bolts (2.1), these bolts attach the
(See Figure 2.)
(See Figure 2.)
and (4) lock nuts to attach the mounting
hardware
at this time.
mount using the hardware
bracket using mounting
hardware
the plastic
shroud
on the winch
winch
models.
to attach
the mount
to the mid-bumper
hardware
tighten
to
for proper
wiring.
Mount
Kit for
mounted winch may result
from
the
ATV
frame.
Follow
torque.
Follow
and use of your winch.
under
the driver
seat of
to disconnect
Figure
provided
with
supplied
with
motor
side to
Figure 2
at this time.
I www.extrememax.com
Honda@
Rincon
Part
# 5600.3154
style # 045001
all
all
-0
1
00
1.2
O
2.1
c
0
1.1
3399ex0120_MET
loading

Sommaire des Matières pour Extreme Max 5600.3154

  • Page 1 Winch Mount Kit for Honda@ Rincon -naäuC7$ Part # 5600.3154 Warning: style # 045001 Risk of personal injury or property damage. An improperly mounted winch may result in a sudden release of the winch mount and/or winch from frame. Follow...
  • Page 2 Product Satisfaction Guarantee At Extreme Max, we pride ourselves on making quality products and wish to correct any mistakes on our end. If you are not 100% satisfied with the product, for any reason, please reach out to us. We are here to help!
  • Page 3 Winch Mount Kit for Honda@ Rincon -naäuC7$ Part # 5600.3154 Attention: style # 045001 Risque de blessures corporelles ou de dommages matériels. Un treuil mal monté peut entrainer une libération soudaine du support de treuil et / ou du treuil du chåssis du VT T.
  • Page 4 Garantie De Satisfaction Du Produit Chez Extreme Max, nous sommes fiers de fabriquer des produits de qualité et souhaitons corriger toute erreur de notre part. Si vous n'étes pas satisfait å 100% du produit, pour quelque raison que ce soit, veuillez nous contacter.