Lamp Replacement; Overhead Rigging - JB Systems Light IROCK 6S Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

ENGLISH
LAMP (RE)PLACEMENT
In case of replacement of the lamp or maintenance,
do not open the fixture within 10 minutes until the
unit cools down after switching off. Always unplug
the unit before servicing! Always use the same type
of spare parts (bulbs, fuses, etc.) When replacing parts, please
only genuine spare parts.
 Switch off the unit and unplug the mains cable.
 Wait for about 10 minutes until the unit has been cooled down.
 Unscrew the 6 screws that close the lamp compartment on the front
of the fixture (A on the picture)
 On the inside you will see the lamp socket. Tear the lamp socket
gently out of the lamp compartment.
 Unplug the old lamp. Hold the lamp socket while unplugging the
lamp instead of pulling the cable! (B on the picture)
 Hold the lamp socket while pressing the new lamp gently in the
socket.
Attention! Check the label on the backside of the device or see the
technical specifications in this manual to know which lamp should be
used. Never install lamps with a higher wattage! Lamps with higher wattage generate temperatures the
device was not designed for. If the device uses a lamp transformer, it will burn due to current overload.
 Don't touch the bulb with bare hands! This drastically shortens the lifespan of the lamp. If you touched the
lamp, clean it with a cloth and a little denatured alcohol. Wipe the lamp off before installing.
 Put the new lamp back inside the unit. Be sure that the wires don't touch the lamp. (C on the picture)
 Close the lamp compartment with the screws.
 Done!
EXCHANGING/ROTATING GOBOS
ATTENTION: Install the gobos only when the unit is switched off!
Never unscrew the screws of the rotating gobo as the ball bearing will be opened. Repairing
this is very difficult!
 Switch off the main supply and unplug the unit.
 Open the plastic top cover (4screws)
 Locate the gobo wheel and remove the fixation ring of
the gobo you want to change with an appropriate tool.
 Remove the gobo and insert the new gobo.
 Press the fixation-ring together and insert it in the front
of the gobo.
 Done!
JB SYSTEMS
®
OPERATION MANUAL
3/57
iROCK 6S-6B
ENGLISH

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
HOW TO SET UP THE UNIT
CONTROL PANEL:
1. DISPLAY shows the various menus and the selected
functions.
2. LEDS
DMX
On
DMX input present
MASTER
On
Master mode
SLAVE
On
Slave mode
SOUND
Flashing
Sound activation
3. BUTTONS
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
4. REMOTE CONTROL INPUT: Used to connect a optional CA-8 hand controller while the unit is used in
standalone or master/slave mode.
JB SYSTEMS
®
OPERATION MANUAL
4/57
iROCK 6S-6B

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Irock 6b

Table des Matières