Chamberlain LiftMaster 892LT Mode D'emploi

Life
The 892LT/894LT remote control is compatible with Security* 2.0TM garage door openers, gate operators,
commercial door operators and commercial receivers. The remote control can also be programmed to
Security* 2.0TM products with encrypted DIP switches. The remote control can also be used as a
replacement for LiftMaster@remote control models 972LM/974LM and 372LM/374LM.
After following the correct programming steps, the 892LT and 894LT remote control will work with
garage door openers or receivers which use the following accessories:
• 890 Series (Security* 2.0TM)
• 370 Series (Security* 315 Mhz)
• 970 Series (Security* 390 Mhz)
The 892LT and 894LT can clone the following DIP switch remote controls:
• 61LM (390 Mhz)
• 361LM (315 Mhz)
• 81ILM (Security+ 2.0TM)
PROGRAMMING
There are two different programming options depending on your application. If you are programming the remote control to an existing DIP switch remote control, refer to OPTIONB. For all other
programming, refer to OPTIONA
OPTION A
The instructions are written for garage door openers, however the
steps still apply for compatible products Make sure the garage door
opener has a working light bulb because it is a programming
indicator. The illustrations are generic, so your garage door opener
may look different
1
Locate the Learn button on the garage door opener (Figure 1)
2
Removethe battery cover from the new remote control and
locate the Program button (Figure 2).
3
To enter programming mode, press the Program button until
the LED on the remote control turns on.
4
Press and releasethe Learn button on the garage door opener.
The Learn LEDwill light. Within 30 seconds.
5
Press and releasethe remote control button that you want to
use.
Check to see if the garage door opener light bulb blinks.
If not, wait for the remote control LEDto light solid then slowly
press and releasethe remote control button again. Repeat until
the light bulb blinks. DONOT press the button after the light
bulb blinks.
6
To exit programming mode, press and releasethe Program
button on the remote control. The LED on the remote control
will turn off.
7
To test, press and releasethe programmed button on the
remote control. The garage door opener will activate.
FIGURE 1
Learn OR Learn
OR
LED
LED
Learn
LED
Learn
Learn
Button
Button
2-BUTTON AND 4-BUTTON
MODEL 892LT
To prevent possible SERIOUSINJURYor DEATHfrom a
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children
NEVERpermit children to operate or play with remote
MODEL 894LT
controls
• Activate gate or door ONLYwhen it can be seen clearly,
is properly adjusted and there are no obstructions to
door travel
• ALWAYS keep gate or garage door in sight until
completely closed NEVERpermit anyone to cross path
of moving gate or door.
OPTION B
1
Make sure the existing dip-switch remote control and the
new remote control are in close proximity to each other.
2
Removethe battery cover from the new remote control and
ccc
locate the Program button (Figure 2)
3
To enter programming mode on the new remote control,
Learn
press the program button until the LEDon the remote
Button
control turns on
4
Press and hold the button that currently activates your
Program
product on the existing remote control that you want to
Button
copy to the new remote control. The LEDon the new remote
control will flash
5
Press and release the button on the new remote control
LED
you want to program. The LEDon the new remote control
will flash rapidly, then return to a flash slowly. DO NOT
FIGURE 2
press the button after the LEDflashes.
6
To exit programming mode, press and releasethe Program
button on the remote control.
control will turn off.
7
To test, press and releasethe programmed button on the
remote control. The gate operator or commercial door
operator will activate
REMOTE CONTROLS
MODELS 892LT AND 894LT
A WARNING
The LED on the remote
that