Cleaning The Air Filter; Cleaning The Housing; At The End Of The Season - Bavaria BMK 2100 E Mode D'emploi

Anleitung_BMK_2100E_2400E_2700E_SPK7__ 09.04.15 14:42 Seite 19
and a signal sounds. The signal can be disabled by
pressing any button. The unit will then be shut down
completely.
When this happens, empty the tray as described
below:
1. Switch off the unit, pull the plug and do not move
the unit.
2. Push a container under the drain screw (1).
3. Unscrew the drain screw (1).
4. Remove the rubber bung (2) from the drain
opening (3).
5. The condensate runs into the container. If the
container is smaller than the condensate tray,
seal the drain opening (3) with the rubber bung
(2) and empty the container. Then repeat the
process from point 4.
6. Once the condensate tray has been completely
emptied, fit the bung (2) and the drainage screw
(1) again.
7. Start the unit again. The "F.W." LED will no
longer flash.
5.11 Draining the condensate with a hose
(Fig. 8-10)
ALL THE CONDENSATE MUST HAVE BEEN
DRAINED BEFORE YOU START THE
FOLLOWING PROCESS.
1. Switch off the unit and pull the power plug.
2. Unscrew the drain screw (1).
3. Remove the rubber bung (2) from the drain
opening (3).
4. Connect the condensate drainage hose (4) and
secure it with a clip
5. The drainage hose can be extended with a hose
(5) with a diameter of 18mm. If you do so, make
sure you use a suitable connector.
Note:
The drainage hose must run to the outside with a
slight fall. The "Condensate tray full" indicator is not
operational.
6. Cleaning, maintance and
ordering of spare parts
To avoid an electric shock or risk of fire,
always pull out the mains plug first before
starting any cleaning work .

6.1 Cleaning the air filter

The air conditioner is fitted with 2 filters.
1. Dust filter (close-meshed filter net)
2. Activated carbon filter (binds particles in the air
and prevents the development of bacteria)
Important: Never use the device without air filters.
1) Dust filter
Remove the filter cover (Fig. 2/Pos. 8-9) by pulling it
to the side and rear.
Then remove the activated carbon filter. Use a
vacuum cleaner or tap the dust filter gently to remove
the dust. If the filter is very dirty, wash it carefully with
warm water. Then allow to dry thoroughly.
2) Activated carbon filter
The activated carbon filter is located behind the top
dust filter and cannot be washed. Its service life is
dependent on the operating conditions. The filter
should be inspected and replaced if necessary. The
filter cover then has to be fitted back on the device
with the activated charcoal filter.

6.2 Cleaning the housing

Use only gentle cleaner and a soft cloth to clean
the housing. Never use aggressive media, petrol,
alcohol or thinner. Only fit the filter back in place
when thoroughly dry.

6.3 At the end of the season

At the end of the season, let the device run for
n
approx. 3 hours in the fan function (FAN).
Then roll up the power cable and store it in the
n
storage compartment provided at the back of the
device (fig. 2/pos. 7).
Place a suitable container beneath the
n
condensate drain and remove the plug. The
trough then empties (see Chapter 5.10).
Re-insert the plug in the condensate drain.
n
Important: If the plug is not inserted or is not
inserted correctly, water will escape the next time
the device is used again.
Clean the filter and the housing.
n
Re-insert the filter when thoroughly dry.
n
Store the device in an upright position, preferably
n
packed in the original box, in a dry and dust-tight
location.
GB
19