Using The Machine - Kobra +2 Mode D'emploi

FEATURES
All Kobra +2 and Kobra +3 models are shredders
suitable for shredding single sheets of paper and 9"1/2
computer print-outs and come with dedicate cutting
blades for shredding CDs, DVDs and CREDIT CARDS.
Only the Kobra +3 models come with the special
patented "Throw and Shred" automatic system for
shredding crumbled paper.
For specifications and shred capacity see table on
page 23.
INSTALLATION
Position the cutting head (1) on the stand (4).
Insert the transparent waste bin for CDs, DVDs and
Credit Cards (3) into the paper bin (2) and insert it fully
into the stand.
The machine is ready for operation.
To empty the transparent waste bin for CDs, DVDs
and Credit Cards (3), extract the paper bin (2) from the
stand (4), slide out the bin for CDs, DVDs and Credit
Cards (3) and once it has been emptied replace it in the
paper bin (2).
To empty the paper bin (2), extract it from the stand
(4), slide out the CD, DVD and Credit Card bin from its
housing, empty the paper bin and then replace the CD,
DVD and Credit Card bin and replace the entire bin in
the metal stand.
WARNING: INCORRECT replacement of the paper bin
prevents the machine from operating properly.
In order to facilitate emptying bins, the paper bin (2)
comes with a transparent blue window on the front
for checking the level of shredded paper as well as
CDs,DVDs and CreditCards in the two separate bins.

USING THE MACHINE

Once the machine has been plugged in, put the button
(A) in the "FWD" position, the ENERGY SMART light (B)
will come on for a few seconds and then, if the machine
is not in use, it will switch off while the machine remains
on STAND-BY at zero power consumption.
Now documents can be shredded at any time.
When the button (A) is at "0" all functions are switched
off.
When button (A) is at "REV", shredding of any kind of
paper or CD, DVD or Credit Card may be interrupted
at any time and the document or data support removed
from the machine.
This function is also possible when the light (B) is off.
SHREDDING PAPER WHICH IS NOT CRUMBLED
Insert sheets of paper through the slit on the front
of either the Kobra +2 or Kobra +3 and the light (B)
comes on (if off). The machine then starts shredding
automatically, activated by two electronic eyes (C)
located inside the slit. These detect the presence of the
paper and the machine automatically switches off a few
seconds after the paper has been shredded.
If the paper inserted exceeds the shred capacity of the
machine, the machine stops and reverses the direction
of the rollers for a few seconds before coming to a halt.
In order to restart the machine, simply flip up and open
the transparent swinging cover (D) and the hand guard
flap (E).
Remove all or some of the unshredded paper and
simultaneously close the hand guard (E) and the
swinging cover (D). The machine restarts automatically
and finishes the shredding with a shred cycle lasting
approx. 15/17 seconds.
SHREDDING CRUMBLED PAPER
Only the Kobra +3 models come with the special
patented "Throw and Shred" system with an automatic
feeder (F) for shredding even crumbled paper.
Open the transparent swinging cover (D), let the
crumbled paper fall into the rear compartment of
the automatic feeder (F) and close the transparent
swinging cover (D) again.
The shredder starts up automatically and stops after
approx. 15/17 seconds.
If more than one sheet of crumbled paper is inserted
at the same time, the machine could jam, go into
automatic reverse and stop.
In order to unjam the machine:
open the transparent swinging cover (D), raise the hand
guard flap (E), remove the crumbled paper from the
shredding chamber and then close the hand guard and
transparent swinging cover again.
The machine will start up automatically for one cycle.
lasting approx. 15/17 seconds to free the cutting blades
and ready the machine for new shred cycles.
SHREDDING CDS, DVDS AND CREDIT CARDS
CDs, DVDs and Credit Cards can be shredded by Kobra
+2 and Kobra +3 models.
Simply lift the transparent swinging cover (D), insert
the magnetic data support in the slot (H) in the hand
guard flap (E) and close the transparent swinging cover
(D) again.
The machine will start up automatically for a shred cycle
lasting approx. 15/17 seconds and stop automatically.
IMPORTANT: only insert one data support at a time
in the slit (H) in the hand guard (E).
8