Directed Electronics XPRESSKIT DLPK Mode D'emploi

Parts required
5 diodes
1 relay
1 22 gauge wire wrap
TRANSPONDER BYPASS
Make 5 to 10 loops
with a 22 gauge wire (-) While Running
(status)
around the valet key
Orange
N.C.
White/Red
Tach Violet/White
(-) While Running (status) Blue/White
Fuel filler door White/Violet
Lock
Light Green
Ignition Pink
1
Light Green
Orange/Brown
Orange/Green
Brown
4
Brake switch
+12V
REMOTE STARTER
(+) Brake In
(+) Starter Out
(-) Starter Out
(+) Ignition In
Connect wire to Remote-Starter/Alarm
AUDI A5
Make 3 to 6 loops
around the front of
the key barrel
30
87a
86
87 85
Vehicle key barrel
View from above
8 1
Yellow
White/Black
~
Hood Trigger
Grey
~
Green Door & Trunk Trigger
Start In
Violet/Black
Unlock
Blue
Trunk
Red/White
14
7
Red connector located
N.C.
at driver kick panel
(CAN Low) Data
Orange/Brown
(CAN High) Data
Orange/Green
STEP 1
CUT
STEP 2
Red/Black
DIODE
1 Amp
Diode required if the
remote starter does
not have (-) starter out
Ignition
1 Amp
Behind fuse box
left side of dash
black wire
Connect wire to vehicle
TECHNICAL
SUPPORT
INFORMATION
2009-2010
updates prior to installation of this product.
Connect:
Orange
White/Red
Violet/White
Blue/White
White/Violet
Lt. Green
Pink
1
12V
2
3
4
86 85
87
87a
30
5
Relay required if the
remote starter does
not have (-) starter out
6
INPUT
OUTPUT
NOTE
web resources:
Once the vehicle has been remote started, the unlock feature must be triggered Once the vehicle has been remote started, the unlock feature must be triggered
www.xpresskit.com
before entering the vehicle otherwise the engine will shutdown once the brake before entering the vehicle otherwise the engine will shutdown once the brake
pedal is pressed. If the unlock feature has been triggered after a remote start, pedal is pressed. If the unlock feature has been triggered after a remote start,
www.xpressvip.com
the lock feature must be triggered in order to shutdown the engine via the the lock feature must be triggered in order to shutdown the engine via the
www.directechs.com
remote starter. remote starter.
U p d at e A l e r t : F i r m w a r e
updates are posted to the web on
a regular basis. We recommend
WWW.XPRESSKIT.COM
you check for firmware and/or install guide
D2D (1 way)
Connect:
8 1
Orange
Yellow
White/Red
White/Black
Grey Violet/White
1 Blue/White
Green
Brown
Orange/Green
White/Violet
violet/Black
Orange/Brown
Lt. Green
Blue
Light Green
Pink
Red/White
4
14
7
Make the connections of the DLPK to the
vehicle:
1.A
Connector 1 (black):
Determine the type of installation:
INSTALLATION WITH D2D
INSTALLATION WITHOUT D2D
1.B
Connector 2 (white):
Make the connections
1.C
Connector 3 (white, located at the back of the module):
Make the connections
Press the programming switch while
inserting the main wires harness (CONN 1)
into the DLPK module.
The LED will illuminate to indicate you are
in programming mode, release the
programming button.
Connect the other connectors
(CONN. 2)
WARNING: Connector 2 can be easily
plugged in backwards.
Connect the other connectors
(CONN. 3)
Turn the key to the ON position.
Once the LED starts to flash rapidly turn
the key to the OFF position.
The LED will turn off to indicate the module
has been programmed.
The module is now ready for use.
DLPK
Rev.: 20100111
D2D (2 way)
8 1
Yellow
White/Black
Grey
Green 1
Brown
Orange/Green
violet/Black
Orange/Brown
Blue
Light Green
Red/White
4
14
7
FUNCTIONALITY