Table des Matières

Liens rapides

Owner's Instruction and Operation Manual
Model Number:
AP5622-W
Report Number: F22-782
Certified to ASTM E1509-2022 and CAN/ULC
S627:2023; Complies to CAN ICES-3(B)/NMB-3(B);
Contains IC:23243-WBR1DIPEX
Mobile Home / Transportable Building Approved
* All Pictures In This Manual Are For Illustrative Purposes Only. Actual Product May Vary.
Save These Instructions In A Safe Place For Future Reference.
SAFETY NOTICE: If this heater is not properly installed, a house fire may result.
For your safety, follow the installation instructions. Never use make-shift
compromises during the installation of this heater. Contact local building or
fire officials about permits, restrictions and installation requirements in your
area. NEVER OPERATE THIS PRODUCT WHILE UNATTENDED.
CAUTION! Please read this entire manual before you install or use your new room
heater. Failure to follow instructions may result in property damage, bodily injury,
or even death. Improper Installation Could Void Your Warranty!
U.S. Environmental Protection Agency
Certified to comply with 2020 particulate
emissions standards.
THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE.
© 2025 United States Stove Company, 227 Industrial Park Rd., South Pittsburg, TN 37380
R
CALIFORNIA PROPOSITION 65 WARNING:
This product can expose you to chemicals including carbon
monoxide, which is known to the State of California to cause
cancer, birth defects, and/or other reproductive harm. For
more information, go to www.P65warnings.ca.gov
854000G-4005N
Ph. 800-750-2723
Table des Matières
loading

Sommaire des Matières pour Ashley AP5622-W

  • Page 1 Owner’s Instruction and Operation Manual Model Number: AP5622-W Report Number: F22-782 Certified to ASTM E1509-2022 and CAN/ULC S627:2023; Complies to CAN ICES-3(B)/NMB-3(B); Contains IC:23243-WBR1DIPEX Mobile Home / Transportable Building Approved 854000G-4005N * All Pictures In This Manual Are For Illustrative Purposes Only. Actual Product May Vary.
  • Page 2 Your pellet stove has been safety tested and listed to ASTM E1509-2022 and CAN/ULC S627:2023. This manual describes the installation and operation of the Ashley AP5622-W pellet stove. This heater meets the 2020 U.S. Environmental Protection Agency’s emission limits for wood-heaters sold after May 15, 2020. Under specific EPA test conditions burning wood pellet fuel this heater has been shown to deliver heat at a rate of 13,640 to 32,591 Btu/hr.
  • Page 3: Installation Checklist

    INSTALLATION CHECKLIST Your Wood Stove should be installed by a qualified installer only. An NFI qualified Installer can be found at www.nficertified.org/public/find-an-nfi-pro/ CUSTOMER SERVICE 1-800-750-2723 ext 5050 Text to 423-301-5624 Email to: Customerservice@usstove.com COMMISSIONING CHECKLIST This checklist is to be completed in full by the qualified person who installs this unit. Keep this page for future reference.
  • Page 4 INSTALLATION FOR CUSTOMER SERVICE CALL: 800-750-2723 EXT 5050 TOP CONTROL MOUNT INSTALLATION 4. Secure the control panel to the top of the stove with two sheet metal screws. Pull the factory installed 5 Pin Main Wiring Harness, 7 Pin Com Cabel, and 4 Pin Wiring Harness, (not shown) out of the top of the stove.
  • Page 5: Door Handle Installation

    INSTALLATION DAMPER HANDLE INSTALLATION DOOR HANDLE INSTALLATION Twist the damper knob clockwise onto the damper Screw the spring handle onto the handle rod. rod. © 2025 United States Stove Company...
  • Page 6 INSTALLATION SAFETY NOTICE CAUTION: • IF THIS STOVE IS NOT PROPERLY INSTALLED, BURNING FUEL CREATES CARBON MONOXIDE A HOUSE FIRE MAY RESULT. TO REDUCE THE AND CAN BE HAZARDOUS TO YOUR HEALTH RISK OF FIRE, FOLLOW THE INSTALLATION IF NOT PROPERLY VENTED. INSTRUCTIONS.
  • Page 7: Installation Options

    INSTALLATION INSTALLATION OPTIONS Canada - Floor protector must comply with CAN/ ULC standards. Must extend 18” (458mm) past the Freestanding Unit - supported by pedestal/legs front and 8” (203mm) beyond each side of unit. and placed on a non-combustible floor surface in compliance with clearance requirements for a freestanding stove installation.
  • Page 8 INSTALLATION SECURING APPLIANCE TO THE FLOOR Use the designated holes to secure the unit to the floor. Exhaust Pipe Fresh Air Intake E Backwall to unit 9.5” 241 mm F Sidewall to flue 13” 330 mm PARALLEL Sidewall to top WARNING! DO NOT INSTALL IN SLEEPING 8”...
  • Page 9: Venting Requirements

    INSTALLATION • Outside Air is mandatory for mobile home/ draft to reduce the possibility of smoke or odor transportable building installation. See Outside during appliance shutdown and keep exhaust from Air Supply section and your dealer for purchasing. causing a nuisance or hazard by exposing people or shrubs to high temperatures.
  • Page 10: Pellet Vent Termination

    INSTALLATION exhaust flow and performance of the stove. Each D. Minimum 7-foot (2.13m) clearance from any elbow or tee reduces draft potential by 30% to 50%. grade when adjacent to public walkways. All joints in the vent system must be fastened by E.
  • Page 11 INSTALLATION This appliance is certified for use with listed 3 inch 11. The exhaust vent pipe must extend at least 12” or 4 inch “PL” pellet venting products. The use of (300 mm) out past the exterior wall. Seal the other components other than stated herein could annular space of the wall thimble and around cause bodily harm, heater damage, and void your...
  • Page 12: Important

    INSTALLATION pipe with a 90-degree turn away from the house. 2. Install the wall thimble as specified by the At this point, a 3ft (0.91m) (minimum) section of manufacturer (wall thimble sold separately) pipe should be added with a horizontal cap, which 3.
  • Page 13: Control Panel Overview

    OPERATION INSTRUCTIONS NEVER OPERATE THIS PRODUCT WHILE UNATTENDED HOW YOUR HEATER WORKS HEAT RANGE Your pellet heater operates on a timer based auger • Pressing the “Heat Range” arrows, up or down, fuel feed system, that is controlled by a digital circuit will adjust the amount of fuel being delivered to board.
  • Page 14: Proper Fuel

    OPERATION INSTRUCTIONS Your pellet stove is designed to burn premium WARNING: hardwood pellets that comply with the Pellet Fuels • DO NOT USE CHEMICALS OR FLUIDS TO Institute (PFI) standard (minimum of 40 lbs density START THE FIRE - NEVER USE GASOLINE, per cubic ft, 1/4”...
  • Page 15: Pre-Start-Up Check

    OPERATION INSTRUCTIONS the stove will shut down. If the stove shuts down CAUTION: push the “On/Off” button to re-start your stove. The • KEEP FOREIGN OBJECTS OUT OF THE stove will have to fully shut down and turn off before HOPPER.
  • Page 16: Opening Door

    OPERATION INSTRUCTIONS OPENING DOOR REFUELLING CAUTION: CAUTION: • DO NOT OPERATE YOUR STOVE WITH • THE HOPPER AND STOVE TOP WILL BE THE VIEWING DOOR OPEN. THE AUGER DURING OPERATION; THEREFORE, WILL NOT FEED PELLETS UNDER THESE YOU SHOULD ALWAYS USE SOME TYPE CIRCUMSTANCES AND A SAFETY CONCERN OF HAND PROTECTION WHEN REFUELING MAY ARISE FROM SPARKS OR FUMES...
  • Page 17 OPERATION INSTRUCTIONS B. In case malfunctioning convection Over time ash or dust may accumulate on the blades blower, the high-temperature thermodisc will of the circulation & exhaust fans. The fans should automatically shut down the auger, preventing be inspected, periodically, and if any accumulation the stove from overheating.
  • Page 18: App Setup

    OPERATION INSTRUCTIONS APP SETUP This stove can be monitored and controlled by using the US Stove Company app which is available for iOS or Android devices through the app store. Download the US Stove Company app. your.email@youremail.com 2. Open the app and select “Sign Up”. Note: You will only need to go through the sign-up process when using the app for the first time.
  • Page 19 OPERATION INSTRUCTIONS APP CONNECTION & OPERATION Open the app. After the initial “Sign Up” process has been completed, the app opens, by default to the “Add Device” screen. 2. Make sure that your device and stove connect to the same Wi-Fi network. 3.
  • Page 20 MAINTENANCE NEVER OPERATE THIS PRODUCT WHILE UNATTENDED at the chimney top. Cooler surfaces tend to build CAUTION: creosote deposits quicker, so it is important to • FAILURE TO CLEAN AND MAINTAIN THIS check the chimney from the top as well as from the UNIT AS INDICATED CAN RESULT IN POOR bottom.
  • Page 21: Painted Surfaces

    MAINTENANCE for extended periods of time. While the modern NOT perform the cleaning while the glass is HOT. combustion systems in heaters drastically reduce Do not attempt to operate the unit with broken the amount of CO emitted out the chimney, glass.
  • Page 22: Maintenance Schedule

    MAINTENANCE MAINTENANCE SCHEDULE Monthly or Daily Weekly Use the following as a guide under average use as needed conditions. Gaskets around door and door glass Burn Pot Stirred Empty should be inspected and repaired or replaced when necessary. Combustion Brushed Chamber Ashes Check...
  • Page 23: How To Order Repair Parts

    HOW TO ORDER REPAIR PARTS For Parts Assistance, Call 800-750-2723 ext 5051 or Email: parts@usstove.com , or order at www.myreplacementparts.com The information in this owner’s manual is specific to your unit. When ordering replacement parts the information in this manual will help to ensure the correct items are ordered. Before contacting customer service write down the model number and the serial number of this unit.
  • Page 24: Troubleshooting Guide

    TROUBLESHOOTING GUIDE When your stove acts out of the ordinary, the first reaction is to call for help. This guide may save time and money by enabling you to solve simple problems yourself. Problems encountered are often the result of only five factors: 1) poor fuel;...
  • Page 25 TROUBLESHOOTING GUIDE DISPLAY “E2” Possible Causes Possible Remedies: (Unplug stove first when possible) Unhook air hose from the air switch and blow through it. Airflow switch hose or stove attachment If air flows freely, the hose and tube are fine. If air will not pipes for hose are blocked.
  • Page 26 TROUBLESHOOTING GUIDE DISPLAY “E3” Possible Causes Possible Remedies: (Unplug stove first when possible) The hopper is out of pellets Refill the hopper. The air dampener is too far open for a low If on the low setting, you may need to close the dampener feed setting all the way.
  • Page 27 TROUBLESHOOTING GUIDE DISPLAY “E4” Possible Causes Possible Remedies: (Unplug stove first when possible) The air inlet, burnpot, interior combustion chambers, combustion blower, Follow all cleaning procedures in the maintenance section exhaust pipe are blocked with ash or foreign of the owner’s manual. material.
  • Page 28 TROUBLESHOOTING GUIDE STOVE FEEDS PELLETS, BUT WILL NOT IGNITE Possible Causes Possible Remedies: (Unplug stove first when possible) In some situations it may be necessary to have the damper completely closed for ignition to take place. After there is Air damper open too far for ignition. a flame, the damper can then be adjusted for the desired feed setting.
  • Page 29 TROUBLESHOOTING GUIDE STOVE WILL NOT FEED PELLETS, BUT FUEL FEED LIGHT COMES ON AS DESIGNED Possible Causes Possible Remedies: (Unplug stove first when possible) Wait for the stove to cool for about 30 - 45 minutes. Locate the High Limit High limit switch has thermodisc and press the reset button on the back of it.
  • Page 30 TROUBLESHOOTING GUIDE HIGH LIMIT SWITCH KEEPS TRIPPING Possible Causes Possible Remedies: (Unplug stove first when possible) The convection blower overheating Clean any dust off of the windings and fan blades. If oiling the blower does not tripping the internal help, the blower may be bad. temperature shutoff.
  • Page 31: Wiring Diagram

    WIRING DIAGRAM                                       ...
  • Page 32: Repair Parts

    REPAIR PARTS Part # Description Part # Description Glass Gasket - Flat 88100 Exhaust Blower Gasket 88174 (3/16T x 3/8W) 80868 Exhaust Blower 893159 Clear Glass 80491 Microswitch 88324 1” Rope Gasket 893241-US Door Handle Kit 893629 Burnpot Assembly Power Receptacle w/ EMC 80917 80455 High Temp Snapdisc...
  • Page 33: Service Record

    SERVICE RECORD It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed. SERVICE PROVIDER Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions. Always use the manufacturer's specified spare part when replacement is necessary.
  • Page 34 NOTES © 2025 United States Stove Company...
  • Page 35: Numéro De Modèle

    Manuel d’instructions et d’utilisation du propriétaire Numéro De Modèle: AP5622-W Signaler Le Numéro: F22-782 Certifié selon la norme ASTM E1509-2022 et Certifié CAN/ULC S627:2023; Conforme à CAN ICES-3(B)/NMB-3(B); Contient IC:23243- WBR1DIPEX Maisons mobiles/bâtiments portatifs approuvé * Toutes les images de ce manuel sont à des fins d’illustration uniquement. Le produit réel peut varier.
  • Page 36 Votre poêle à granulés a été testé pour la sécurité et homologué selon ASTM E1509-2022 et CAN/ULC S627:2023. Ce manuel décrit l’installation et le fonctionnement du poêle à granulés Ashley AP5622-W. Cet appareil de chauffage respecte les limites d’émission de l’Agence américaine de protection de l’environnement 2020 pour les appareils de chauffage au bois vendus après le 15 mai 2020.
  • Page 37: Liste De Contrôle D'installation

    LISTE DE CONTRÔLE D’INSTALLATION Votre poêle à bois ne doit être installé que par un installateur qualifié. Un installateur qualifié NFI est disponible à l’adresse www.nficertified.org/public/find-an-nfi-pro/ SERVICE CLIENTS 1-800-750-2723 poste 5050 Texte au 423-301-5624 E-mail à: customerservice@usstove.com LISTE DE CONTRÔLE DE MISE EN SERVICE Cette liste de contrôle doit être remplie intégralement par la personne qualifiée qui installe cet appareil.
  • Page 38: Installation Du Support De Commande Supérieur

    INSTALLATION POUR LE SERVICE À LA CLIENTÈLE, APPELEZ : 800-750-2723 EXT 5050 INSTALLATION DU SUPPORT DE Fixez le panneau de commande sur le dessus du poêle avec deux vis à tôle. COMMANDE SUPÉRIEUR Tirez le faisceau de câbles principal à 5 broches, le câble de communication à...
  • Page 39: Installation De La Poignée Du Registre

    INSTALLATION INSTALLATION DE LA POIGNÉE DU INSTALLATION DE LA POIGNÉE DE PORTE REGISTRE Vissez la poignée à ressort sur la tige de la poignée. Tournez le bouton du registre dans le sens des aiguilles d’une montre sur la tige du registre. ©...
  • Page 40 INSTALLATION AVIS DE SÉCURITÉ ATTENTION: • SI CE POÊLE N’EST PAS INSTALLÉ CORRECTEMENT, • UN DÉTECTEUR DE FUMÉE FONCTIONNEL DOIT INCENDIE PEUT RÉSULTER. POUR ÊTRE INSTALLÉ DANS LA PIÈCE OÙ SE TROUVE RÉDUIRE LES RISQUES D’INCENDIE, SUIVEZ LES LE POÊLE. INSTRUCTIONS D’INSTALLATION.
  • Page 41: Dégagements

    INSTALLATION OPTIONS D’INSTALLATION Canada - Le protecteur de plancher doit être conforme aux normes CAN/ULC. Doit s’étendre de 18 po (458 mm) Unité autoportante - supportée par un piédestal / pieds au-delà de l’avant et de 8 po (203 mm) au-delà de chaque et placée sur une surface de plancher incombustible côté...
  • Page 42: Fixation De L'appareil Au Sol

    INSTALLATION FIXATION DE L’APPAREIL AU SOL Utilisez les trous désignés pour fixer l’unité au sol. Tuyau D'échappement Air frais Admission AVERTISSEMENT ! - N’INSTALLEZ PAS L’APPAREIL DANS UNE CHAMBRE A COUCHER ATTENTION ! - L’INTEGRITE STRUCTURELLE DU PLANCHER DE LA MAISONS MOBILES/BÂTIMENTS PORTATIFS, DES MURS ET DU TOIT DOIT ETRE Mur arrière à...
  • Page 43 INSTALLATION • Vérifiez auprès de vos responsables locaux du bâtiment « PL » de 3 po (76 mm). La longueur totale de l’évacuation car d’autres codes peuvent s’appliquer. horizontale NE DOIT PAS dépasser 4 pi (1,22 m). Ceci pourrait provoquer une contre-pression. N’utilisez pas EXIGENCES POUR L’EVACUATION plus de 180 degrés de coudage (deux coudes à...
  • Page 44: Terminaison D'évent À Granulés

    INSTALLATION moyens pour maintenir le pare-vapeur entre l’extérieur D. Dégagement minimum de 7 pi. (2,13 m) au-dessus de et l’intérieur de la maison. Les surfaces de ventilation tout passage public. peuvent devenir suffisamment chaudes pour provoquer Dégagement minimum de 2 pi. (0,61 m) au-dessus de des brûlures si elles sont touchées par des enfants.
  • Page 45: Grâce À L'installation De Mur

    INSTALLATION Cet appareil est certifié pour une utilisation avec 12. Installez un bouchon de terminaison horizontal approuvé ou si nécessaire installer un coude à 90 ° énuméré 3 pouces ou 4 pouces “PL” produits granulés de ventilation. L’utilisation d’autres composants autres que et la longueur appropriée de ventilation verticale.
  • Page 46: Ventiler Votre Poêle À Granulés Dans Un Système De Cheminée Existant De 6 Po

    INSTALLATION VENTILER VOTRE POÊLE À GRANULÉS installation peut être utilisée si votre chauffe-eau est en dessous du niveau du sol en ajoutant simplement la DANS UN SYSTÈME DE CHEMINÉE section de nettoyage et tuyau vertical intérieur jusqu’à ce EXISTANT DE 6 PO que le niveau du sol est atteint.
  • Page 47: Présentation Du Tableau De Commande

    INSTRUCTIONS D’UTILISATION INSTALLATION NE JAMAIS UTILISER CE PRODUIT SANS SURVEILLANCE COMMENT FONCTIONNE L’APPAREIL DE • L’appui sur le bouton « OFF » du tableau de commande déclenche la séquence d’arrêt de l’appareil. Le système CHAUFFAGE d’alimentation en combustible arrête de distribuer le Cet appareil de chauffage à...
  • Page 48 INSTRUCTIONS D’UTILISATION INSTALLATION Votre poêle à granulés est conçu pour brûler des granulés AVERTISSEMENT: de bois dur de qualité supérieure conformes à la norme • N'UTILISEZ PAS DE PRODUITS CHIMIQUES OU PFI (Pellet Fuels Institute) (densité minimale de 40 lb par DE FLUIDES POUR ALLUMER LE FEU - N'UTILISEZ pied cube, diamètre de 1/4 à...
  • Page 49: Vérification Avant La Mise En Marche

    INSTRUCTIONS D’UTILISATION INSTALLATION est ouverte alors que le poêle est en marche, elle doit être AVERTISSEMENT: fermée dans les 30 secondes ou le poêle s’éteindra. Si le • GARDER LES OBJETS ÉTRANGERS HORS DE LA poêle s’éteint, appuyez sur le bouton « Marche/Arrêt » TRÉMIE.
  • Page 50: Ventilateur De La Pièce

    INSTRUCTIONS D’UTILISATION INSTALLATION OUVERTURE DE LA PORTE RECHARGE EN COMBUSTIBLE Si la porte est ouverte pendant le fonctionnement du AVERTISSEMENT: poêle, elle doit être refermée dans les 30 secondes, sinon le poêle s’éteint. Si le poêle s’éteint, appuyez sur • GARDEZ COUVERCLE TRÉMIE...
  • Page 51 INSTRUCTIONS D’UTILISATION INSTALLATION arrête automatiquement la tarière, ce qui prévient Au fil du temps, de la cendre ou de la poussière peuvent s’accumuler sur les pales des ventilateurs de circulation une surchauffe du poêle. et d’extraction. Les ventilateurs doivent être inspectés REMARQUE: Sur certains appareils, une fois le bouton de périodiquement et, en cas d’accumulation, les nettoyer réinitialisation déclenché, comme un disjoncteur, il faut...
  • Page 52: Configuration De L'application

    INSTRUCTIONS D’UTILISATION INSTALLATION CONFIGURATION DE L’APPLICATION Ce poêle peut être surveillé et contrôlé à l’aide de l’application US Stove Company qui est disponible pour les appareils iOS ou Android via l’App Store. Téléchargez l’application US Stove Company. votre.email@votreemail.com Ouvrez l’application et sélectionnez “S’inscrire”. Remarque : vous n’aurez besoin de passer par le processus d’inscription que lorsque vous utiliserez l’application pour la première fois.
  • Page 53: Connexion Et Fonctionnement De L'application

    INSTRUCTIONS D’UTILISATION INSTALLATION CONNEXION ET FONCTIONNEMENT DE L’APPLICATION Ouvrez l’application. Une fois le processus initial d’« inscription » terminé, l’application s’ouvre, par défaut, sur l’écran « Ajouter un appareil ». Assurez-vous que votre appareil et votre poêle se connectent au même réseau Wi-Fi. Assurez-vous que le poêle est branché...
  • Page 54: Entretien

    ENTRETIEN NE JAMAIS UTILISER CE PRODUIT SANS SURVEILLANCE ainsi que par le bas. La créosote doit être éliminée AVERTISSEMENT: avec une brosse spécialement conçue pour le type de • LE DÉFAUT DE NETTOYAGE ET D’ENTRETIEN cheminée utilisé. Un ramoneur qualifié peut fournir ce DE CET APPAREIL COMME INDIQUÉ...
  • Page 55 ENTRETIEN sont en bon état de fonctionnement et d’étanchéité Une fois le radiateur refroidi, retirez la porte du correctement pour assurer une exposition involontaire. Il radiateur. est recommandé d’utiliser les deux écrans de fumée et Retirez le joint de corde de la porte, puis les écrous de CO dans les zones ayant le potentiel de générer CO.
  • Page 56: Calendrier D'entretien

    ENTRETIEN CALENDRIER D’ENTRETIEN Toutes Tous les Tous les mois ou Suivez le calendrier ci-dessous dans des conditions jours selon les besoins d’utilisation moyennes. Les joints autour de la porte et de semaines la vitre doivent être inspectés et réparés ou remplacés si Pot de combustion Agité...
  • Page 57: Commande De Pièces De Rechange

    COMMANDE DE PIÈCES DE RECHANGE Pour une assistance pièces, appelez le 800-750-2723 poste 5051 ou envoyez un e-mail : parts@usstove.com, ou commandez sur www.myreplacementparts.com Les informations contenues dans ce manuel du propriétaire sont spécifiques à votre appareil. Lors de la commande de pièces de rechange, les informations contenues dans ce manuel vous aideront à...
  • Page 58: Guide De Dépannage

    GUIDE DE DÉPANNAGE Lorsque le poêle ne fonctionne pas comme d’ordinaire, la première réaction est de demander à l’aide. Ce guide peut vous faire gagner du temps et économiser de l’argent en vous permettant de résoudre les problèmes simples par vous-même.
  • Page 59 GUIDE DE DÉPANNAGE L’ÉCRAN AFFICHE « E2 » Solutions possibles: (Débranchez le poêle avant toute chose Causes possibles quand c’est possible.) Débranchez le tuyau souple d'air de l'interrupteur de débit Le tuyau souple de l'interrupteur de débit d'air ou les d'air et soufflez dans le tuyau.
  • Page 60 GUIDE DE DÉPANNAGE L’ÉCRAN AFFICHE « E3 » Solutions possibles: (Débranchez le poêle avant toute chose Causes possibles quand c’est possible.) La trémie est vide de granulés. Remplissez la trémie. Le registre de réglage d'air est trop ouvert pour un Si le réglage de chauffage est réduit, vous devrez peut-être réglage de chauffage trop bas.
  • Page 61 GUIDE DE DÉPANNAGE L’ÉCRAN AFFICHE « E4 » Solutions possibles: (Débranchez le poêle avant toute chose Causes possibles quand c’est possible.) L'entrée d'air, le pot de combustion, les chambres de combustion internes, les ventilateurs de combustion Suivez toutes les procédures de nettoyage de la section ou le conduit d'évacuation sont bouchés par des d'entretien du Guide d'utilisation.
  • Page 62 GUIDE DE DÉPANNAGE L’ÉCRAN AFFICHE « E5 » Solutions possibles: (Débranchez le poêle avant toute chose quand c’est Causes possibles possible.) Le capteur du thermostat a été débranché du tableau de commande. Vérifiez Le poêle affiche automatiquement si le capteur est débranché. Si le capteur n’est pas débranché, c’est le capteur «...
  • Page 63 GUIDE DE DÉPANNAGE UNE ODEUR DE FUMÉE EST REFOULÉE DANS LA PIÈCE Solutions possibles: (Débranchez le poêle avant toute chose quand c’est Causes possibles possible.) Inspectez tous les raccords de tuyaux d'évacuation. Assurez-vous qu'ils soient tous scellés avec du silicone RTV supportant une température de 500 °F (260 Il y a une fuite dans le système de °C) ou plus.
  • Page 64 GUIDE DE DÉPANNAGE LE POÊLE N’EST PAS ALIMENTÉ EN GRANULÉS, MAIS LE TÉMOIN D’ALIMENTATION EN COMBUSTIBLE S’ALLUME COMME PRÉVU Solutions possibles: (Débranchez le poêle avant toute chose quand c’est Causes possibles: possible.) Attendez que le poêle refroidisse pendant environ 30 à 45 minutes. Localisez le thermodisque de surchauffe et appuyez sur le bouton de réinitialisation L'interrupteur de surchauffe s'est situé...
  • Page 65 GUIDE DE DÉPANNAGE L’INTERRUPTEUR DE SURCHAUFFE SE DÉCLENCHE TOUT LE TEMPS Solutions possibles: (Débranchez le poêle avant toute chose quand Causes possibles c’est possible.) Enlevez la poussière des bobinages et pales de ventilateur. Si le Le ventilateur de convection surchauffe et graissage du ventilateur ne suffit pas, il se peut que le ventilateur déclenche l'arrêt de température interne.
  • Page 66: Pièces De Rechange

    PIÈCES DE RECHANGE Clé Partie Description Qté Clé Partie Description Qté Joint de verre - Plat (3/16T x Joint de ventilateur 88174 4 pi 88100 3/8W) d'échappement 893159 Verre propre 80868 Ventilateur d'échappement 88324 Joint de corde de 1 po 5 pi 80491 Micro-interrupteur...
  • Page 67: Schéma De Câblage

    SCHÉMA DE CÂBLAGE              É   ÈÊ    Ô      Â  À  É     È  ...
  • Page 68: Enregistrement De Service

    ENREGISTREMENT DE SERVICE Il est recommandé que votre système de chauffage est desservi régulièrement et que le Service Interval enregistrement approprié est terminée. FOURNISSEUR DE SERVICES Avant de terminer l’enregistrement de service approprié ci-dessous, s’il vous plaît vous assurer que vous avez effectué le service tel que décrit dans le les instructions du fabricant.

Table des Matières