Technical Specifications; Safety Instructions; Usage Instructions; Maintenance And Storage - Hudora Stunt Scooter XX-222 Instructions De Montage Et Mode D'emploi

INSTrUcTIoNS oN ASSemBLY AND USe
EN
coNGrATULATIoNS oN
PUrchASING ThIS ProDUcT!
Please read these instructions carefully. The instructions are an integral
component of the product. Therefore, please store them and the packa-
ging carefully in case questions arise in the future. Please always include
these instructions when giving the product to a third party. This product
must be assembled by an adult. This product is not designed for indus-
trial use. The use of the product requires certain capabilities and skills.
Always adjust according to the age of the user and use for the purpose it
has been designed for.

TechNIcAL SPecIFIcATIoNS

Item: Stunt Scooter XX-222 //
Stunt Scooter YY-11, XY-12
Item number: 14112 // 14120, 14121
Dimensions: 65x56x82 cm // 66,5x56x82,5 cm
Item weight: 4 kg // 3,9 kg
Maximum user weight: 100 kg (valid for all models)
If you have assembly problems or would like further information on the
product, we have all you need and more at http://www.hudora.de/.
coNTeNTS
1 x Scooter Deck with back wheel and front wheel fork
1 x Scooter handlebars
1 x Front wheel
1 x Front wheel axis
2 x Allen wrench M5
1 x ICS bolt with washer
1 x Instructions
Other items included are meant to facilitate safe transportation and are
not required for the installation and use of the product.

SAFeTY INSTrUcTIoNS

• The scooter is only intended for use by one person.
• Only use the scooter on surfaces that are suitable for it, i.e. those which
are flat, clean, dry, and use the scooter where possible away from other
road users. Avoid sloping ground. The brakes may become hot if the
scooter has been used for a while! They shouldn't be touched until they
have cooled down.
• Always be considerate of others.
• Wear suitable protective clothing for your own safety. Never use the
scooter without a helmet and hand/wrist, elbow and knee pads. Never
use the scooter without shoes!
• Before you start. Ensure that all fasteners and locking parts are intact
and tight; the functioning of the self-locking threads can slacken after
repeated loosening and tightening of the fasteners. Check especially for
the correct alignment and fastening of the steering set-up.
• Do not use the scooter at twilight, at night or in poor visibility. Do not
use it on roads or thoroughfares or on slopes or hills. Avoid being in the
proximity of stairs and open water.
• The scooter is not a vehicle in the sense of the road traffic regulations!
It is intended for use on footpaths.
ASSemBLY INSTrUcTIoNS
Slide the bar onto the fork tube after first loosening the clamp screws.
Place the stunt scooter on it's side, onto a clean flat surface. Please note
the fork has to be positioned 90 degrees to the bar. Fit the threaded bolt
by use the washer through the fork into the Aluminium insert, located in
the bar. Tighten the threaded bolt so there is no gap between the Bar and
the head set. Check by revolving the Bar for smooth operation. Tighten
the screws holding the clamp to the bar Check the Bar is fixed securely to
the fork tube before use. Attach the front wheel to the fork by use an allen
key to help align the screw. Tighten the wheel screws by means of the 2
All images are examples of the design.
Allen keys M5 provided. Check by moving the wheel from side to side to
ensure there is no shaking. Always check before use, any removable parts
are correctly tightened. To take apart the scooter, please follow these di-
rections in reverse.

USAGe INSTrUcTIoNS

NOTHING'S EASY AT FIRST ...
... most accidents happen to "beginners" within the first ten minutes. Par-
ticular care should be taken during this stage.
USAGE INSTRUCTIONS
The scooter moves when a foot is used to regularly push off, just as with
well-known children's scooters. Braking is no problem either - simply
step on the friction brake over the back wheel (mudguard).

mAINTeNANce AND STorAGe

Use a dry or damp cloth only to clean the product; do not use special
cleaning agents! Check the product for damage or traces of wear and tear
before and after each use. Do not make any structural changes. For your
own safety, please use original spare parts only. These can be sourced
from HUDORA. If parts become damaged or if sharp edges or corners
should develop, the product may not be used any more. If in any doubt,
please contact our service team (http://www.hudora.de/). Store the pro-
duct in a safe place where it is protected from the elements, cannot be
damaged, and cannot injure anyone.
WHEEL CHANGE
Replacement wheels are available as accessories from http://www.hu-
dora.de and should be replaced when they are worn down. However, it is
usually advisable to change the bearings when the wheels are changed.
To change the wheels, loosen the axle fitting with two size 5 Allen keys
and take the wheels off the axle. A screwdriver or Allen key can be used
to push the bearings out of the wheel to use them in the new wheel. Put
the bearings into the new wheel with the bolt spacer and mount them to
the frame with the axle screws. Make sure the axle has been screwed on
tightly before starting again!
BEARINGS
Your scooter is equipped with precision ball bearings which were filled
with lubrication at high pressure during manufacture. For this reason, the
wheels only run easily and quickly when there is a load on the scooter.
The bearings are maintenance free. If a bearing should fail, it should be
replaced completely. Bearings are available as accessories from http://
www.hudora.de.
DISPoSAL ADVIce
At the end of the product's life, please dispose of it at an appropriate coll-
ection point provided in your area. Local waste management companies
will be able to answer your questions on this.
SerVIce
We make every effort to deliver faultless products. If faults do arise how-
ever, we put just as much effort into rectifying them. Therefore, you can
find numerous information on the product, replacement parts, solutions
to problems and lost assembly manuals at http://www.hudora.de/service.
3/8