Publicité
English
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These chemicals
may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any
liquid get inside the tool; never immerse any part of the tool
into a liquid.
Storage
CAUTION: Never store with liquid inside the pump.
• Store in a dry, covered location above freezing
temperature. sTORE inDOORs.
To store the DCE050 pump:
‑ Remove the battery pack.
‑ Remove the inlet and outlet hoses from the pump.
‑ Pour out any excess water from the pump.
‑ Run the pump for no more than five seconds to clear out any
remaining water. Freezing temperatures can cause remaining
water in the pump to freeze and could damage the pump.
‑ Install the two hose connection caps
Accessories
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the
risk of injury, use only D
WALT accessories recommended for
e
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
D
WALT Tool Tag Ready (Fig. L)
e
Optional Accessory
Your tool comes with tool tag mounting holes
fasteners
28
for installing a D
a T15 bit tip to install the tag.
WARNING: Use only original fasteners. Longer screws
increase the risk of electrical shock or damage to the tool.
The D
WALT Tool Tag is designed for tracking and locating
e
professional power tools, equipment, and machines using
the D
WALT Tool Connect™ app. For proper installation of
e
the D
WALT Tool Tag refer to the D
e
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should be
performed by a factory service center or an authorized service
center. Always use identical replacement parts.
6
10
.
WALT call 1-800-4-D
WALT
e
e
29
and
WALT Tool Tag. You will need
e
WALT Tool Tag manual.
e
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/account‑login.
Three‑Year Limited Warranty
For warranty terms, go to
www.dewalt.com/support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
WALT
e
WALT
e
Publicité
