Dario tools CMB.515750 Mode D'emploi page 31

ob Teile beschädigt sind. Sämtliche
Teile müssen richtig montiert sein
und alle Bedingungen erfüllen, um
den einwandfreien Betrieb des
Gerätes zu gewährleisten.
Beschädigte Schutzvorrichtungen
und Teile sollen sachgemäss durch
eine Kundendienstwerkstatt repariert
oder ausgewechselt werden, soweit
nicht anderes in den
Bedienungsanleitungen angegeben
ist. Benützen Sie keine Werkzeuge
bei denen sich der Schalter nicht ein-
und ausschalten lässt.
21. ACHTUNG! Zu Ihrer eigenen
Sicherheit benützen sie nur Zubehör
und Zusatzgeräte, die in der
Bedienungsanleitung angegeben
oder vom Werkzeug-Hersteller
empfohlen oder angegeben werden.
Der Gebrauch anderer als der inder
Bedienungsanleitung empfohlenen
Einsatzwerkzeuge oder Zubehörteile
kann eine persönliche
Verletzunggefahr für Sie bedeuten.
22. Reparaturen nur vom
Elektrofachmann. Dieses
Elektorwerkzeug entspricht den
einschlägigen
Sicherheitsbestimmungen.
Reparaturen dürfen nur von einer
Elektrofachkraft ausgeführt werden,
anderfalls können Unfälle den
Betreiber entstehen.
BEWAHREN SIE DIE
SICHERHEITSHINWEISE GUT AUF!
SAFETY INSTRUCTIONS
IMPORTANT! When using electrical tools,
the following safety instructions should be
observed to prevent the risk of electric shock,
personal injury and fire. Read and observer
these instructions carefully before using the
tool.
1. Keep work area clean. Cluttered
areas and benches invite injuries.
2. Consider work area environment. Do
not expose power tools to rain. Do
not use power tools in damp or wet
locations. Keep work area well lit. Do
not use power tools near flammable
liquids of gases.
3. Guard against electric shock.
Prevent body contact with grounded
surfaces (e.g. pipes, radiators,
ranges, refrigerators etc).
4. Keep children away. Do not let
visitors contact tool or extension
cord. All visitors should be kept away
from work area.
5. Store idle tools. When not in use, tools
should be stored in a dry, high or
locked-up place, out of reach of children.
6. Do not force tool. It will do a better job
and operate more safely at the rate for
which it was intended.
7. Use right tool. Do not force small tools
or attachments to do the job of a heavy
duty tool. Do not use tools for another
than their intended purpose; for example
do not use a circular saw for cutting tree
limbs or logs.
8. Dress properly. Do not wear loose
clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-
skid footwear are recommended when
working outdoors. Wear protective hair
covering to contain long hair.
9. Use safety glasses. Also use a dust
mask during pulverulent operations and
wear ear protection. If the noise level
exceeds 85 dB(A), ear protection is
obligatory. Indicated noise levels may be
exceeded dependent on the working
environment and the material to be
treated.
10. Use dust extraction. If dust extraction
and collection devices are present on
the tool, make sure that they will be
used properly.
11. Do not abuse cord. Never carry tool by
cord or yank it to disconnect it from wall
outlet. Keep the cord from heat, oil and
sharp edges.
12. Secure work. Use clamps or a vise to
hold the workpiece. It is safer and it
frees both hands to operate tool.
13. Do not overreach. Keep proper footing
and balance at all times.
14. Maintain tools with care. Keep tools
sharp and clean for better and safer
performance. Follow instructions for
lubricating and changing accessories.
Inspect tool cords periodically and, if
damaged, have them repaired by an
authorized service facility. Inspect
extension cord periodically and replace
if damaged. Keep handles dry, clean
and free form oil and grease.
15. Disconnect tools. When not in use,
before servicing, and when changing
accessories such as blades, bits and
cutters.
16. Remover adjusting keys and wrenches.
Form the habbit of checking to see that
key and adjusting wrenches are
removed from the tool before switching it
on.