Innokin Z Biip Guide De Démarrage Rapide

O V E R V I E W
1
Cap
2ml Capacity Pod
Z-PLEX3D KAL Coil [0.48Ω]
Air Flow Control Ring
3X Clicks On/Off
Z-Biip Internal Rechargeable
Battery (1500mAh)
Power Indicator Window
=16W =14W =11W
Micro USB Charge Port
Battery Life Indicator
FULL HALF RECHARGE
Disable Audible Indicators
C H A R G I N G
4
ATTACH THE MICRO USB CHARGE CABLE TO THE DEVICE AND
THE OTHER END TO A USB POWER SOURCE.
THE WHITE LED INDICATOR LIGHTS WILL ILLUMINATE LETTING
YOU KNOW THE DEVICE IS CHARGING.
WHEN CHARGING IS COMPLETE, THE WHITE LED INDICATOR
LIGHTS WILL TURN OFF AND THE DEVICE WILL BEEP 5X.
A D J U S T I N G T H E P O W E R L E V E L
5
TURN THE DEVICE OFF SEE USAGE.
PRESS AND HOLD THE SIDE ACTIVATION BAR.
THE DEVICE WILL BEGIN TO CYCLE THROUGH THE THREE POWER
LEVELS AND DISPLAY THOSE LEVELS AS COLORS IN THE POWER
INDICATOR WINDOW.
= HIGH 16W
= MEDIUM 14W
= LOW 11W
ONCE THE INDICATOR DISPLAYS THE DESIRED POWER LEVEL,
RELEASE THE ACTIVATION BUTTON.
TURN THE DEVICE BACK ON SEE USAGE.
THE DEVICE WILL NOW FIRE IN YOUR DESIRED POWER LEVEL
AND INDICATE THAT LEVEL IN THE POWER INDICATION WINDOW.
All manuals and user guides at all-guides.com
P R E PA R E T H E P O D F O R U S E /
2
C H A N G I N G T H E C O I L
HOLD THE POD FROM BOTH SIDES AND GENTLY LIFT
UP ON ONE OF THE SIDES. THE POD WILL RELEASE.
UNSCREW THE AIRFLOW CONTROL RING.
REMOVE THE COIL.THE POD SHOULD BE
PARTIALLY DRAINED BEFORE REMOVING
THE COIL OR E LIQUID COULD ESCAPE.
PRIME THE COIL. ADD 3 4 DROPS OF
E LIQUID ONTO THE COIL.
REPLACE THE COIL AND AIRFLOW
CONTROL RING.
ADJUST THE AIRFLOW CONTROL
RING TO A DESIRABLE DRAW.
REPLACE THE POD. THE DEVICE WILL BEEP
ONCE LETTING YOU KNOW THE POD IS
INSERTED CORRECTLY.
NEVER DISCARD THE AIRFLOW CONTROL RING. THIS IS A REUSABLE
PART. NEW PODS WILL NOT COME STANDARD WITH THIS PART.
U S A G E
6
POWER ON/OFF.
CLICK 3X
POWER ON/OFF
WHEN POWERING ON, THE WHITE LED BATTERY
INDICATORS WILL ACTIVATE FROM THE BOTTOM UP.
WHEN POWERING OFF, THE WHITE LED BATTERY
INDICATORS WILL ACTIVATE FROM TOP DOWN.
WITH THE DEVICE ON AND THE POD PREPARED AND FILLED,
DEPRESS THE SIDE ACTIVATION BUTTON AND DRAW FROM THE
MOUTHPIECE.
AS YOU'RE USING THE DEVICE AND THE BATTERY BEGINS TO
DRAIN, THE DEVICE WILL WARN YOU WITH AUDIBLE INDICATORS.
POWER BELOW 50% = 2 BEEPS
POWER BELOW 20% JUST ABOUT TIME TO CHARGE = 3 BEEPS
QUICK START GUIDE(EN)
H O W T O F I L L T H E Z - B i i P P O D
3
TWIST THE TOP CAP WHICH WILL
EXPOSE THE FILL PORT. NOTE THAT
THE POD DOES NOT NEED TO BE
REMOVED FROM THE DEVICE.
FILL HERE
(DO NOT OVER FILL)
INSERT THE E LIQUID APPLICATOR
PAST THE SILICON FILL PORT SEAL.
ANGLE THE DEVICE SO THE LIQUID
FLOWS DOWN INTO THE POD.
WIPE UP ANY EXCESS LIQUID
TWIST THE CAP TO CLOSE THE POD.
NOTE: ALTHOUGH MOST LIQUIDS NOW COME IN SQUEEZE BOTTLES,
SOME STILL COME IN DRIPPER BOTTLES. IF YOU ARE USING A
DRIPPER BOTTLE AND ARE HAVING A HARD TIME FILLING, WE HAVE
SUPPLIED A SQUEEZE BOTTLE IN THE KIT TO MAKE FILLING EASIER.
A U D I B L E I N D I C AT O R S
7
CORRECT POD ATTACHMENT AND CONNECTION = 1 BEEP
POWER BELOW 50% = 2 BEEPS
POWER BELOW 20% JUST ABOUT TIME TO CHARGE = 3 BEEPS
CHARGE COMPLETE WHEN CHARGING = 5 BEEPS
D I S A B L E A U D I B L E I N D I C AT O R S
8
TURN THE SWITCH OFF ON THE BOTTOM OF THE DEVICE.
OFF ON