Instructions For Assembly And Use; Optional Accessory Use; For Best Results - Thane H2O SteamFX Pro Guide D'utilisation

Instructions for Assembly and Use

1. Find the Water Tank located in the appliance re-heats and will
the box. Remove the Water Tank turn ON again once it reaches the
Cap and fill with water to the "MAX" operating temperature. However,
fill indicator line on the water tank, the appliance will continuously
and then secure the water tank cap emit steam, as long as the Steam
in place. Place under the main unit Switch is pressed and water tank
is filled with water, regardless if the
and screw into position following
the Lock & Unlock marking on the Indicator turns ON.
Water Tank RED light will remain ON when
plugged in.
2. Attach an accessory to
Steam Outlet as indicated in the IMPORTANT! Do not touch the
"Accessories Usage" section. nozzle or any other attachments as
they can get hot.
3. Plug the appliance into an
electrical outlet. The Red Indicator 5. Slowly Pass over the surface to
Light will turn ON. be cleaned.
4. Wait approximately 20-30 6. To stop emitting steam release
seconds. When the steamer is the Steam Switch button.
ready to emit steam the Green
Indicator Light will turn ON. Press IMPORTANT: After the Steam
and hold the Steam Switch Switch is turned OFF steam will
to emit steam. continue to flow for a short period
of time (approximately 10 – 15
Note: During usage the Green seconds) until all steam inside the
Indicator Light will turn OFF when entire system is released.
8
7. When the appliance stops emitting
steam it means that the Water Tank
needs to be refilled. Release the
Steam Switch button and unplug the
appliance from the electrical outlet.
Fill the Water Tank with water as
described in step 1 and then follow
steps 3-5 above.
Using the Safety Lock:
The Safety Lock can be used 2 ways.
1. Press the Safety Lock to the locked
position when the unit is
powered on to prevent accidentally
activating the Steam Switch to
produce steam.
2. Press the Safety Lock to the locked
position when pressing the
Steam Switch down to produce steam.
This allows you to release your thumb
from the Steam Switch. Simply click
the Steam Switch again or press down
on the Safety Lock to deactivate it and
stop the steam.
Optional Accessory Usage
Assembling the Mop Accessory
1. Assemble the 3 Extension Pipes by fitting the steam outlet
into the opening of the next Extension Pipe and the final
Extension Pipe into the Mop Head as indicated in Fig. A.
Tip: You can adjust the height of the unit by using 2
Extension Pipes instead of 3.
2. Attach the Extension Pipe to the Steam Outlet of the
main unit as shown in Fig. B.
3. Attach the Mop Cloth to the Mop Head by attaching it to
the underside of the Mop Head as shown in Fig. C
4. When using the H2O SteamFX™ Pro on carpeting or
rugs; Place the Mop Head with Microfiber Cloth in place,
on top of the Carpet Glider as illustrated. Do not attempt to
use the H2O SteamFX™ Pro on carpeting or rugs without
the Carpet Glider in place. Only use the microfiber cloth on
carpets. Never use the Carpet Glider on surfaces that are
prone to scratching.
5. When finished remove the Mop Cloth from the Mop Head
and wash as needed.
WARNING:
Before using, make sure the mop has been assembled with
Mop Cloth attached to the Mop Head to prevent damage.
Notice: This product emits steam and creates moisture.
Water marks, discoloration or damage to the floor surface
can occur if the unit is left operating too long in one place.
Never leave the H2O SteamFX™ Pro Handheld Steamer
unattended while plugged in.
Fig (A)

For Best Results:

1. Sweep or vacuum floor prior to using the H2O SteamFX™ Pro Handheld Steam
Cleaner.
2) To avoid puddling of water, the Microfiber Cloth must be clean and dry for
use. To replace the cleaning cloth, proceed as follows: Let the cleaning cloth
cool down, remove cloth from unit, replace with a new Microfiber Cloth
(Optional Item) and continue use.
3) To sanitize an area of your floor, leave the H2O SteamFX™ Pro Handheld
Steam Cleaner over the steam area for about 10 seconds, but no longer than
15 seconds. Do not carry out this procedure on heat and steam sensitive floors.
• Never steam at one spot for too long. This can cause floor surface damage.
• Do not put hands or feet under the steam mop. Unit gets very hot.
• During use, a pulsing noise may be heard indicating that the mop is
producing steam. This noise is normal.
• There may be some minor "spitting" of water mixed with the steam. This is
also normal.
• The force and heat of the steam may adversely affect certain materials.
Always check the suitability of using the steam mop on a surface by
carrying out a preliminary test on a hidden area.
Fig (C)
Fig (B)
9