Extension Tubes - Robusta DRY STEAM Manuel D'utilisation

EN
Attachment Compartment
The steam hose fitted with the steam gun must be
connected to the unit and the attachment needed must
be fitted before the steam generator is switched on. The
DRY STEAM possesses an attachment compartment for
holding the long nozzle, the two round brush nozzles and
the curved nozzle (fig. 1A). Lift up the yellow cover (fig.
1B). Open the attachment compartment by pulling the
transparent cover forwards (fig. 1C). Take out the steam
attachment you require and put the transparent cover back
in place. The space below the yellow cover is the steam
channel for connecting the extension tube. Just open the
yellow cover if you only need to iron an item of clothing.
1) Steam Gu
All the cleaning attachments are used in conjunction with
the steam gun. Firstly, connect the steam gun hose to the
steam channel in the DRY STEAM. To do this, tip up the
black flap on the cover (fig. 2A) and push the connector on
the steam hose firmly into the steam connector socket until
it clicks into position (fig. 2B). To remove the steam supply
hose, simultaneously depress the two release buttons
positioned on either side of the steam connector and pull
the hose out of the socket.
2) Pot de Mesure et Entonnoir
The steam cleaner must always be disconnected from the
mains supply for filling or emptying. Unscrew the tank cap
by pushing it downwards and twisting it anti-clockwise
at the same time (fig. 3A). Use the measuring jug and
funnel for filling with water (fig. 3B) and do not exceed the
maximum capacity when filling. Put the safety cover back in
place. Push it downwards and turn it clockwise.
If the steam flow-rate drops, water must be added to the
unit. Stop the steam generator by pressing on the ON/OFF
switch. Press the steam trigger on the steam gun to release
any remaining steam; disconnect from the mains, open the
safety cap and let the unit cool down. Warning: oress the
cap downwards and turn it anticlockwise to open. Put the
cap back in place after the unit has cooled down completely
and has been refilled with water. Reconnect to the mains
(fig. 4A) and re-start (fig. 4B). The unit can be used again
as soon as the indicator lights come on.
Warning
Hot steam may escape when opening the cap!
There is a risk of being burnt by the threads on the cap and
the tank.
3) Attachment adaptor
The steam generator includes a wide range of nozzles that
can be fitted for cleaning different surfaces both fast and
efficiently. Firstly assemble the attachment adaptor so that
its mounting clips are in the right place in relation to the
steam tube. The attachment adaptor can be fitted directly
to the steam gun and the extension tubes.
Check that the adaptor is fully pushed in place and has
clicked into position (fig. 5). To remove the adaptor, depress
the corresponding release button and pull the adaptor
downwards.

4) Extension tubes

Assemble the extension tubes if the steam cleaner is to be
used for cleaning floors or areas that are difficult to reach.
To do this, push the open end of the tube into the steam
gun until the release button clicks into position (fig. 6). Add
one, two or all five extension tubes if necessary. To remove
an extension tube, depress the corresponding release
button and remove the tube by pulling it downwards.
5) Long nozzle
The long nozzle can be used separately for cleaning, or it
can be fitted with the brush nozzle, the curved nozzle, the
brush spray unit or the flat spray unit. The long nozzle is
mainly used for cleaning openings. Insert the nozzle into
the attachment adaptor (fig. 7) and firmly rotate 90° in the
direction indicated by the arrow marked on the nozzle.
6) Curved nozzle
This nozzle is designed for easy cleaning of areas that are
difficult to reach, such as corners, frames and toilets.
Just push the curved nozzle into the attachment adaptor
to hold it in place (fig. 8). It can be removed by pulling it
downwards.
13