BRINKS 7253 Instructions D'installation

Congratulations on your purchase of a Brink's 42Watt Compact Fluorescent Lamp Yard Light fixture. You have purchased a safe,
dependable, easy-to-install security lighting system. You can use this fixture at home for outdoor lighting applications.
WHAT'S INCLUDED:
A – Metal Pole Clamp B – Fixture Housing
F – Clamp Nut G- Canopy Mounting Plate
TOOLS YOU WILL NEED:
Metal Silicone Sealant or Caulk, Phillips Screwdriver and Adjustable Wrench
A
G
RISK OF FIRE. MAINTAIN AT LEAST 2 INCH SPACING BETWEEN FIXTURE HOUSING AND THE MOUNTING SURFACE.
IMPORTANT SAFETY INFORMATION
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE INSTALLATION CODES.
• IF YOU ARE NOT FAMILIAR WITH ELECTRICAL WIRING, IT IS RECOMMENDED THAT YOU SECURE THE SERVICES OF A WELL QUALIFIED
ELECTRICIAN WHO CAN ASSURE THAT THIS INSTALLATION MEETS LOCAL, STATE, AND NATIONAL CODES. THIS PRODUCT MUST BE
INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
• BE SURE POWER IS TURNED OFF AT THE MAIN POWER PANEL OR FUSE BOX PRIOR TO INSTALLATION OR REPLACING FIXTURE.
• Before installing this fixture, be sure to check with local ordinances regarding approved outdoor lighting. This fixture style may not be allowed in some areas.
• This fixture is for outdoor use only.
• This fixture is for wall mount or pole mount installation only.
• The electrical system and the method of connecting the fixture to the system must be in accordance with local, state, and national electric codes.
• This fixture is to be connected to a 120 volt, 60 Hz power source. Connecting to a different power source may create a hazard and will void the warranty.
• This fixture is suitable for wet locations.
• Do not use near or around flammable/combustible material or liquids.
• The compact fluorescent lamp (bulb) and fixture can get hot during use. Turn off the power and allow the fixture to cool down for at least 20
minutes prior to working on the unit.
• For non-ballasted compact fluorescent lamp (CFL) use only. Use a 42 Watt non-ballasted compact fluorescent lamp (Brink's® Model No. 7054) when
replacing the lamp (bulb). Do not use an incandescent or any other type of lamp (bulb) in this fixture. Do not use a lamp (bulb) with a higher wattage
than the stated maximum (42 Watt) allowed on the fixture. Using a higher wattage lamp (bulb) may cause a fire hazard and/or damage to the unit.
• This compact fluorescent lamp does not have a ballast. Not for use with direct current circuit.
• Compact fluorescent lamp is fragile. Always use safety precautions. Glass is breakable. Safety glasses and gloves should be worn during
installation. To prevent lamp from cracking, avoid holding glass while unscrewing or screwing in lamp. Handle by base.
• Normal starting temperature -20°F (-28°C). NOTE: In extreme cold weather, a compact fluorescent lamp (CFL bulb) initial lumen output may be
dimmer than normal and may take time to warm up.
• Risk of electric shock. Do not attempt to open the fixture housing or lamp. There are no serviceable parts inside.
• Fixture must not be installed facing reflective surfaces closer than five (5) feet.
• Carefully read through the entire installation instructions before installing this security light fixture.
NOTE
• This fixture is equipped with a photo cell which automatically turns off the light during the day light.
To check if fixture is operable during daylight hours, or to bypass photo sensor as your desire, simply cover the
photo sensor with duct tape or black electric tape.
• For pole installation, recommended pipe size is within Ø1-5/8" overall.
• Not intended for use with emergency exit fixtures of lights, electronic timers, motion detectors, or dimmer switches.
• Lamp contains Mercury. Dispose of safely and in accordance with applicable local and federal ordinances.
INSTALLATION INSTRUCTIONS
LOCATION
• Select a location on a structurally sound, flat wall or pole 10-25 feet above the ground.
• Fixture should be located on wall or pole at least 18 inches below any overhang or other structural detail.
• Fixture should not be recessed and must be positioned with bulb in vertical position and bulb socket base up.
• 120v/60Hz power must be available at the desired location. If not, have a qualified electrician route power to that location.
C – Wire Connectors (3)
H – 42 Watt Compact Fluorescent Lamp (Brink's Model No. 7054)
B
Hg
Manage in Accord
with Disposal Laws
H
SECURITY LIGHTING SYSTEMS
INSTALLATION INSTRUCTIONS
D – Mounting Screws (2)
C
D
LAMP
CONTAINS
MERCURY
Model No. 7253
E – Clamp Screw
J – Plastic Lens
E
F
J
PHOTO
SENSOR