Meteor™ Docking Station Installation Instructions; Important Safety Information - Garmin Meteor 300 Instructions D'utilisation

Meteor™ Docking Station Installation
Instructions
You can install this docking station to protect and connect your
compatible smartphone or media player to a Garmin
device. You can also install this docking station without
connecting it to a Meteor device to protect your compatible
smartphone or media player and connect it to a charger.

Important Safety Information

See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite
side of the surface.
Contacting Garmin Product Support
• Go to www.garmin.com/support
for in-country support information.
• In the USA, call (913) 397.8200 or (800) 800.1020.
• In the UK, call 0808 2380000.
• In Europe, call +44 (0) 870.8501241.
Mounting the Docking Station
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case
and the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
Before mounting the docking station, you must choose a
location where there is at least 155 mm (6
behind the mounting surface, and there is enough clearance for
the open door of the docking station as indicated on the
template.
1
Trim the template and make sure it fits in the location where
you want to mount the docking station.
2
Adhere the template to the location where you want to mount
the docking station.
3
3 Using a 9.5 mm ( / in.) drill bit, drill the hole inside the
8
corner of the dashed line on the template to prepare the
mounting surface for cutting.
4 Using a jigsaw or rotary tool, cut the mounting surface along
the inside of the dashed line indicated on the template.
5
Place the docking station in the cutout to test the fit.
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the docking station fits correctly in the cutout, ensure
the mounting holes on the docking station line up with the
pilot holes on the template.
8
If the mounting holes on the docking station do not line up,
mark the new pilot-hole locations.
3
9
Using a 2.6 mm ( / in.) drill bit, drill the pilot holes.
32
10 Remove the template from the mounting surface.
11 Place the gasket on the back of the docking station
12
Place the docking station in the cutout.
2
® Meteor
WARNING
CAUTION
NOTICE
and click Contact Support
NOTICE
1
/ in.) of clearance
8
13
Secure the docking station to the mounting surface using the
included screws
14
Select an option:
• Route the USB cable away from sources of interference
and connect it to the Meteor device.
• Route the USB cable and connect it to a charger
approved for your smartphone or media player.
NOTE: The docking station must be connected to the
Meteor device to play media using the USB input.
Media Player and Smartphone Compatibility
Only media players and smartphones with ports on the bottom,
not on the sides, fit in the docking station.
Devices larger than 144 × 71 × 13 mm (5
not fit in the docking station.
You can use the included adapter cables to connect popular
media players and smartphones to the docking station.
Cable Connector
Micro-USB connector
Apple ® 30-pin connector
Apple Lightning™ connector
You also can connect a USB flash drive containing media files
directly to the USB port on the docking station. A connected
USB flash drive must be formatted as FAT32 or NTFS.
Connecting a Media Player or Smartphone
Before you connect a media player or smartphone, you must
mount the docking station.
1
Open the docking station door, and slide out the device tray.
2
Insert the adapter cable
NOTE: You can connect a USB flash drive directly to the
USB port.
.
.
9
/ × 2 ¾ × ½ in.) do
16
Devices
Media players and smartphones
that support Media Transfer
Protocol (MTP), including most
Android™ devices.
Apple iPhone ® 4s, iPhone 4,
iPhone 3G, iPod touch
through 4th generation), iPod
classic ® , and iPod nano
through 6th generation).
Apple iPhone 5, iPod touch (5th
generation), and iPod nano (7th
generation).
into the USB port
® (2nd
® (4th
.