Jotul FS 280 Série Manuel D'installation page 16

eNglish
4.3 The surround consists of the following
parts (Fig. 1C):
Part Designation
1 Bottom plate
2 Screw, hexagon with flange M8 x 40 DIN6921
3 Leg
4 Screw hexagon, M8x30 Elzn DIN 933
5 Protective hood, M8 6K black
6 Threaded bar, M8 x 70
7 Long nut, M8 x 30
8 Allen nut with flange M8 untreated DIN 6923
9 Side plate
10 Blind rivet nut M6
11 Mounting bracket
12 Spacer sleeve heat shield
13 Screw, hexagon with flange M6 x 10 special
14 Nut M6 DIN 934
15 Heat shield front
16 Sleeve Ø 10/6.2 x 10
17 Top plate
18 Screw, machine countersunk poz M6 x 25
black chrome DIN965
19 Approval label
20 Front plate
21 Steel shelf
22 Door damper Ø7, thickness 1.5
23 Ash lip, steel
24 Rear piece
25 Screw plate pan head poz 4.8 x 16 Elzn DIN 7981
Installation using top outlet
The product is supplied from the factory with the smoke outlet
fitted for the top outlet. See Fig. 5.
• Thread the flue pipe (optional extra) through the top plate
grate and place it in the smoke outlet.
• Make sure that the gasket is properly seated between the flue
pipe and the smoke outlet.
• Fit the connection in the flue pipe.
See measurements under "3.7 Steel chimney".
NB: It is important for the joints/flue pipes to be sealed completely.
Air leaks may prevent them from operating properly.
Installation using a rear outlet
Rear outlet can be installed in accordance with Fig. 1A+1B.
Installation of console (Fig. 6)
1. Secure an adjustment screw with protective hood into each
of the four legs. Fit the bottom plate (part 1) to the legs. Use
the four screws provided. Make sure that the legs are straight.
Tighten the screws.
Installation of console on the burn chamber
1. Screw a long nut on each of the four threaded bars (part 7).
The threaded bars must go 8-10 mm through the long nuts.
See Fig. 7.
16
2. Screw the threaded bars onto the burn chamber. Tighten the
screws (Fig. 8).
3. Secure the console to the burn chamber using four nuts. Do
not completely tighten the nuts. Allow a play of 3-4 mm. Adjust
Quantity
the long nuts to leave approximately 33-34 mm between the
x1
bottom plate (part 1) and the burn chamber. See Fig. 9.
x8
4. Stand the burn chamber up with the help of another person.
x4
NB: Cover the floor to protect it from sharp edges.
x4
5. Refit the rear heat shield (cast iron) by first hanging it on the
x4
upper screws. Raise it slightly and slide it down onto the lower
x4
screws. Tighten the screws.
x4
6. Check that the fireplace is level.
x4
x2
Measurements: There should be approx. 60 mm between the front
x8
of the console and the edge of the door. See Fig. 9.
x1
x4
Installation of steel surrounding set (surround)
x4
x4
1. Unscrew the four screws on the top of the burn chamber
x1
(Fig.10).
x4
2. Hold one of the side plates (part 9) and turn it so that the
x1
transversal holes are on the front.
3. Fold down the lap at the bottom of the side (inside).
x4
4. Lift and turn the side approx. 45
x1
of the console and angle it downwards.
x2
5. Do the same on the opposite side.
x1
6. Secure the sides with the mounting brackets (part 11). Hook
x3
the laps on the mounting brackets to the sides. Push the spacer
x1
sleeves under the plate and secure with screws.
x1
7. Fit four nuts and screws on the upper part of the sides (inside).
x10
See Fig. 11 A.
8. Install the heat shield by attaching it in the keyhole opening.
See Fig. 11 B.
9. Mount both the front panels (part 20). See Fig. 12.
10. Adjust the burn chamber, if necessary, by screwing the long
nuts between the burn chamber and bottom plate. The
distance between the burn chamber door and the upper front
is 6 - 8 mm.
11. Push the shelf (part 21) in from the side and let it rest against
the bottom plate.
12. Place door dampers (part 22) on the shelf and put the ash lip
in place (part 23).
13. Screw the rear plate into position with the screws supplied.
14. With a rear outlet, remove the knockout.
15. Fit the top plate as illustrated in Fig. 13.
16. Fit the top grate on the knobs in the top plate. Turn the top
grate so that the slots fit onto the knobs.
. Push it in between the legs
o