Accessories; Environmental Protection - PALSON City Mode D'emploi

GB
Hose storage:
For your comfort, the vacuum cleaner has a groove on its side to put the floor accessory and hose into
when you are going to move or put it away (Fig. 6).

ACCESSORIES

1. The accessories can be directly inserted on the handle removing the telescopic tubes and inserting
the required accessory.
2. The accessories can also be fitted to the telescopic metal tube for reaching greater distances.
Remove the head for combination of floors and insert the required accessory.
Accessory for grilles (10): for grilles, corners, grooves, etc.
Accessory for upholstery (1): for carpets, upholstery, stairs, etc+.
DUST CONTAINER AND FILTERS
Removal and replacement:
- Cleaning the filters whenever the dust container is emptied is recommended for the machine to
operate at optimum capacity.
- Always unplug the vacuum cleaner from the socket before removing the dust container.
- Do not use the vacuum cleaner without all of its filters installed.
Emptying the dust container:
1. Press the container release button (14) and lift up the dust container (Fig. 7).
2. Hold the container over a rubbish bin and press the container opening button (15) as indicated to
empty the container. When all of the dust has been emptied, close the container's lid, until you hear
a click. Then put the dust container back in (Fig. 8).
Filter cleaning:
1. Turn the dust container around and remove it (Fig. 9). Remove the first filter, turn the multicyclonic
filter 90 º clockwise, and then pull it out.
2. The multicyclonic filter should be cleaned with a soft brush. Then clean it with a damp cloth. The
dust container can be rubbed until clean (Fig. 10).
3. Leave the filters to dry totally before putting them back in.
IMPORTANT:
The multicyclonic filter should not be put under water.
Do not use detergents or boiling water for washing the filters. Cleaning the filter every time the waste
container is emptied is recommended.
4. Put the container back in as indicated.
Hepa filter cleaning:
This filter is on the back of the vacuum cleaner.
1. Release the Hepa filter lid and remove it as indicated. Remove the filter pulling the flap towards
you (Fig. 12).
2. The filter can be knocked against the side of a rubbish bin to remove excess dirt and dust.
3. The Hepa filter can be washed in lukewarm (max. 40 degrees, Fig. 13). Leave it to dry for 24 hours
before putting it back in.
NOTE:
Do not use detergents or boiling water for cleaning the filters. Washing the filter once every 9-12
months is recommended.
4. When it is totally dry, put the Hepa filter back into the vacuum cleaner. Put the Hepa filter lid back
on before turning the vacuum cleaner on.
STORAGE
Always unplug the vacuum cleaner from the socket and pick up the cable as indicated before putting
the vacuum cleaner away.
14
TROUBLESHOOTING
To minimise the risk of injuries, unplug the vacuum cleaner before carrying out maintenance/
troubleshooting checks.
PROBLEM
The vacuum cleaner does not It is not correctly plugged in
work
The socket has no electricity
The on/off (I/O) switch has not
been activated
The motor thermostat has
triggered
Blown fuse/tripped switch
The vacuum cleaner does not Dust container not correctly
hoover installed
Dust container full or blocked
Blocked filters
The accessories do not The accessories have not
hoover been correctly fitted
The hose is not correctly
installed
Dust comes out of the The dust container is full
vacuum cleaner
The dust container is not
correctly installed
The filter is not correctly
installed

ENVIRONMENTAL PROTECTION

Discarded electrical products must not be thrown away with household garbage. This device must be
brought to its local recycling center for safe processing.
Thank you for choosing one of our products.
CAUSE SOLUTION
Plug it in correctly
Check the fuse or the switch
Turn the on/off (I/O) swtich to "on"
Turn the vacuum cleaner off and
unplug it. Wait for an hour before
turning it on again
Put the switch back or replace
the fuse
Check that the container is
correctly installed
Empty the dust container
Remove, clean and replace the
filters
Consult the "Accessories" point
Consult the "Assembly" point
Empty the container
Check that the container is
correctly installed
Remove, clean and replace the
filters
15