Wall Installation; Ceiling Installation - Screen Research CLCTS Manuel D'installation

ENGLISH - Screen user manual
Our screens are suitable for indoor use at normal temperature (20 - 25 °C) and humidity conditions. Special precautions are necessary for outdoor use, especially as regards
temperature levels and the presence of dust. Exposure to temperatures of over 50 °C can cause permanent deformation of the screen's flatness, or the screen to come away
from the roller.
Avoid prolonged exposure of the projection screen to solar light to prevent yellowing of the same (ensure that exposure to solar light does not cause the screen to reach said
temperature level).
Since electrostatic charge tends to accumulate on the projection screen (which is made of PVC), attracting dust, excessive dustiness in the projection environment can
deteriorate the optical quality of the screen (see projection screen cleaning instructions).
WARNING: Do not manually force the screen's unrolling: this could result in the motor being damaged or the screen's case to come away from the wall mount brackets.
Do not allow children to play with the screen's control panel. Keep remote control out of children's reach.
Monitor screen movement and allow no-one near it until it is completely closed.
The following operations: blocking, preventing or forcing the screen's movement, hanging or swinging from it, adding or applying any object to the screen or backdrop,
modifying the screen's structure – are strictly forbidden and could result in damages to the screen's rolling system and ensuing hazard to persons and things.
Screens and their projection surfaces are delicate and must be cleaned with great care, according to the following instructions:
Never use solvents, chemical or abrasive products, or pointed tools to clean the surface.
Avoid contact with other materials (varnishes, inks etc) as they might be impossible to remove from the canvas.
FABRIC CLEARPIX FABRIC FABRIC FABRIC CLEARPIX CLEARPIX CLEARPIX: Use a soft, clean, dampened cloth, wiping from the center of the projection surface towards the outer edges. A vacuum-cleaner brush may be used, provided its bristles are soft and
perfectly clean.
FABRIC SOLIDPIX, MULTIPIX, FABRIC FABRIC FABRIC SOLIDPIX, MULTIPIX,: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary. SOLIDPIX, MULTIPIX, SOLIDPIX, MULTIPIX,
Clean the projection screen with a soft, clean, damp cloth, and a neutral or alcohol-base detergent as necessary. Since rubbing the screen with a cloth during cleaning operations can cause electrostatic
charge to accumulate, we recommend the subsequent application of an antistatic liquid with a clean cloth, to avoid dust being attracted again
FABRIC SILVERPIX FABRIC SILVERPIX is Mandatory to read the instructions accompanying the fabric screen FABRIC SILVERPIX FABRIC SILVERPIX
GENERIC PROFIL GENERIC PROFILE E E E : : : : Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary
GENERIC GENERIC PROFIL PROFIL
VELVET PROFILE: Clean profile with a soft clean cloth, or a brush with soft, antistatic bristles. A vacuum-cleaner brush may be used, provided its bristles are soft and perfectly clean. VELVET PROFILE VELVET PROFILE VELVET PROFILE
STRUCTURE and ANCHORING BRACKETS: The state of the product and the anchoring capacity of its brackets must be checked regularly. In case of canvas deformation or rips, or loosening of structural STRUCTURE and ANCHORING BRACKETS:
STRUCTURE and ANCHORING BRACKETS: STRUCTURE and ANCHORING BRACKETS:
components such as brackets or screws, action must be taken immediately to clear the area around the screen and avoid hazard to people and things, replace the defective component and restore the
product's functionality.
WARNING: WARNING: It 's absolutely forbidden to install the screen on mobile walls or unstable cables,the brackets must be applied on surfaces that ensure in the time your distance. When WARNING: WARNING:
installing the screen use plugs and screws suitable for the screen's weight and for the type of wall or ceiling on which the mount brackets are to be fixed, based on the following criteria
Screen width up to cm Screen width up to cm Screen width up to cm Screen width up to cm
Overall weight Overall weight
Overall weight Overall weight
Made by Adeo Screen sp. Z o.o. (Polska) Specifications are subject to change without notice. E&OE
Please verify that you are working with the latest revision of this document before specifying your screen.
Doc: Manual CLCTS-CLCLT rev5 | 03.02.2015| Download at: www.screenresearch.com 2015 AdeoSreen All Rights Reserved.
05 05 05 05 WARNINGS AND RECOMMENDATIONS FOR CORRECT USE WARNINGS AND RECOMMENDATIONS FOR CORRECT USE WARNINGS AND RECOMMENDATIONS FOR CORRECT USE WARNINGS AND RECOMMENDATIONS FOR CORRECT USE
06 06 06 06 CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE
07 07 07 07 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS

WALL INSTALLATION:

WALL INSTALLATION: WALL INSTALLATION: WALL INSTALLATION:
Insert screw 4 with thread turned upwards into plate 1 and screw on nut 3 loosely, leaving a 4-5 mm play; hook plate 1 to the case and insert plastic pin 2 into
the slot of the small bracket. Please note that, for assembly purpose, the plate can be mounted either way since the hookable sections of the case are perfectly
symmetrical. Secure bracket 5 to the wall with adequate wall type expansion plugs (min. Ø 8 mm) and secure plate 1 to bracket 5 using washer 7 and bolt 3.

CEILING INSTALLATION:

CEILING INSTALLATION: CEILING INSTALLATION: CEILING INSTALLATION:
secure ceiling brackets 6 (provided) with adequate wall expansion plugs (min. Ø 8 mm), at approx. 10 - 15 cm from the ends of the case. For screens wider
than 350 cm, the third bracket must be positioned in the middle of the case. Insert screw 4 with thread turned upwards into plate 1 and screw on nut 3
loosely, leaving a 4.5 mm play; hook plate 1 to the case and insert plastic pin 2 into the slot of the small bracket. Secure plate 1 to bracket 6 using washer 7
and bolt 3.
Direct ceiling installation with mount plates:
For closer adherence of the case to the ceiling it is possible to fix mount plates 1 directly to the ceiling (N.B.: for quick and easy performance of this operation,
excellent ceiling flatness and perfect alignment of the plates are required). Secure the plates with expansion plugs suitable for the type of ceiling (min. Ø 8
mm), at approx. 10 - 15 cm from the ends of the case. For this type of installation, as a rule, the side of the plate in which the pin is to be slotted should be
turned towards the front of the case, to facilitate the insertion of the pin. Carefully check the alignment and horizontality of the plates. Metal washers of the
type included in the packaging may be used for the purpose as necessary. Note that an accurate performance of this operation will ensure ease and speed
when subsequently hooking the case to the plates. For screens wider than 350 cm the third palte must be positioned in the middle of the case. Hook the case
to the plates with a semicircular movement (until it clicks into position); secure the case to the plates by inserting the plastic pins
QUICK BRACKET VERSION INTALLATION QUICK BRACKET VERSION INTALLATION: : : :
QUICK BRACKET VERSION INTALLATION QUICK BRACKET VERSION INTALLATION
1)secure brackets with adequate expansion plugs (min. Ø 8 mm); ceiling or wall mount are possible; check they are level;
2) fasten screen to brackets as the left pictures
160 160 160 160 200 200 200 200 250 250 250 250 300 300 300 300
Kg 20 Kg 20 Kg 25 Kg 25 Kg 30 Kg 30 Kg 35 Kg 35
Kg 20 Kg 20 Kg 25 Kg 25 Kg 30 Kg 30 Kg 35 Kg 35
360 360 360 360 410 410 410 410 520 520 520 520 620 620 620 620
Kg 45 Kg 45 Kg 50 Kg 50 Kg Kg Kg Kg 100 100 Kg 150 Kg 150
Kg 45 Kg 45 Kg 50 Kg 50 100 100 Kg 150 Kg 150
Page 7