Fortin INT-SL Guide Rapide

1
Make the connections of the INT-SL to the
vehicle:
1.A Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH DATA-LINK
INSTALLATION WITHOUT DATA-LINK
Connector 2 (White):
1.B
Make the connections
Press and hold the programming
2
button. Plug in the
in the INT-SL interface.
The LED will turn on, indicating
3
the beginning of programming.
Plug the
INT-SL interface.
4
WARNING: Connector 2 can be easily
plugged in backwards.
While holding the programming
5
button, turn the key to the ignition
position.
6
The LED will flash rapidly.
7
Release the programming button.
8
Start the vehicle with the key.
9
The LED will turn off.
10
Turn the key OFF.
The interface is programmed.
BUICK Park Avenue
FONCTIONNAL IF EQUIPPED
R
Bypass PK3, Passlock or VATS
R
Doorlock Control
R
Factory Alarm Control (OEM)
R
Trunk Release
R
Door status
WITH DATA-LINK
connector 1
connector 2 into the
WITHOUT DATA-LINK
Connect wire to Remote-Starter/Alarm
Copyright © 2009, FORTIN AUTO RADIO INC
1999-2005
DATA INTERFACE MODULE FOR SECURITY SYSTEM / REMOTE STARTER.
£
Heated Seats and Heated
Mirrors (Heated seats will turn
ON (low power) ONLY if the
engine temp is below 0°C
(32°F) when remote started.)
Lt. Blue
N.C.
White
N.C.
Ignition Pink
2
Blue
N.C.
Door trigger Orange
~
Data OBD2 Purple
PIN 2
Yellow
N.C.
2
1 2 3 4 6 7 8
5
9 10 11 12 13 14 15 16 WARNING: Connector 2 can be easily
plugged in backwards.
1
Lock Lt. Blue
Unlock Driver 1 White
Ignition Pink
(-) While running Blue
2
Orange
Door trigger
Data OBD2 Purple
Yellow
N.C.
PIN 2
2
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
1
Cut off one plug of the Data-Link connector, connect the
red wire to +12V and the black wire to ground.
Connect wire to vehicle
Technical support:
TEL: 514-255-HELP (4357)
FAX: 514-255-1367
Web: www.ifar.ca
ALL RIGHTS RESERVED
INT-SL
WEB
Made in Canada - Rev.B- 03 / 04 / 2009
UPDATE
W e b s i t e : h t t p : / / w w w . i f a r . c a
£
£
Rear Defrost
R £
Parking Light Control
R R
Retained Accessory Power
R R
Memory selection Driver 1 and
R
2 (by Unlock)
Lt. Blue/Black
N.C.
In Data-Link mode the analog Input
White/Black N.C.
(unlock, ground out) are disabled for
Pink/Black
N.C.
security.
Green N.C.
Orange/Black Tach
Starter or alarm
Purple/White or Purple/Black
N.C.
Yellow/Black
N.C.
Lt. Blue/Black
Trunk
White/Black
Unlock Driver 2
Pink/Black Parking Light
Green
N.C.
Tach
Orange/Black
~
Purple/White or Purple/Black N.C.
Yellow/Black N.C.
WARNING: Connector 2 can be easily
plugged in backwards.
Red +12V
Black
Neither the manufacturer or distributor of this module is
responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this
module in case of manufacturing defects. This module must
be install by qualified technician. This instruction guide may
change without notice. Visit www.ifar.ca to get latest version.
Start
Slidding doors
Tach
Hand Brake Data-Link
Foot Brake Data-Link
Data Link Port
OUTPUT INPUT