Satco NUVO S11880 Instructions D'installation

LED 4" & 6" FIRE RATED LOW PROFILE
DIRECTIONAL DOWNLIGHTS WITH
REMOTE DRIVER
Models: S11880, S11881
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
• Make sure power is OFF before installation or any
maintenance of the fixture.
• To avoid damage, falling, electric shock or fire, do not modify
the fixture or replace accessories without confirming with the
supplier first.
• Only authorized, qualified personnel should install this fixture
and should follow the owner's manual.
• Do not dismantle the fixture without the supplier's authorization.
• Do not touch the power supply when the fixture is operating.
• For use in environments where an accumulation of
non-conductive dust on the fixture may be expected.
• Suitable for indoor wet and damp locations.
• Suitable for insulated ceiling.
• Type IC Rated for direct contact with insulation.
IMPORTANT:
This product must be installed in accordance
with the applicable installation code by a person familiar with the
construction and operation of the product and the hazards involved.
Model Finish Dimensions
S11880 White
S11881 White
INSTALLATION
TOOLS REQUIRED: Hole saw, measuring tape and connector cables (as needed).
NOTE: Use extensions if necessary. Available connector cables are 6' (1.8m).
Connector cables are linkable.
1. Turn power OFF from the electrical panel before starting installation.
2. Cut a hole in the ceiling for the downlight in a suitable position. Refer to Hole Cut
Dimension chart (below).
3. Run the electrical wire from the switch (power supply wire) through the mounting
hole. Use NMD90 Romex or BX cable. See Figure B.
4. Open the Junction Box swing cover and remove the appropriate knockouts.
5. Insert the power supply wire through the knockout and fasten with a cable connector
(not included).
6. Connect wires inside the Junction Box using the quick connect terminals. Connect
green ground with the green box wire. Connect the black and white power leads
with the matching black and white box wires. See Wiring Diagram.
7. Put all wires and connections back into the box and close the cover securely.
8. New Construction Applications: Junction Box shall be firmly secured to the
studs, joists or similar fixed structural units.
Remodel Applications: Do not require the Junction Box to be firmly secured to
fixed structural units.
9. Choose the color temperature using the switch on the side of the remote driver.
See Figure A.
10. Bend back the two torsion springs and slowly fit the fixture through the ceiling hole.
The torsion springs will pull the fixture into place. See Figures C & D.
11. Once installation is complete, turn power ON to confirm the fixture is working properly.
Hole Cut Dimensions:
4" Round: Ø 4 1/4" (108mm) | 6" Round : Ø 6 5/16" (160mm)
2-HOUR FIRE RATED PROTECTION
• Tested to comply with bulding construction requirements UL 263-2011(R2022)
ASTM E119-22 & CAN/ULC-S101-14-REV1
• Tested and approved for a fire resistant rating of 2-hours with fire rated wood joist
floor-ceiling assembles.
© Copyright 2023 Satco Products, Inc. 8/23 v1.4
Watts Volts
4 inches 9W
120V
6 inches 15W
The wiring compartment or junction box has a volume of 140 cubic
centimeters, which is suitable for a maximum of 6-12AWG 90ºC
through branch circuit conductors.
The cable entry is calculated using Two 12 AWG Branch circuit
conductors entering, Two 12 AWG Branch Circuit conductors exiting,
and Two 12 AWG insulated Grounding connectors. This enclosure
complies with the National Electric Code.
Figure A:
CCT Selection Switch
CCT Selectable CRI
2700K/3000K/
90
3500K/ 4000K/5000K
Figure A:
CCT Selection
Switch
WIRING DIAGRAM
Figure B
Figure C
Figure D
Satco Products, Inc.
Brentwood, NY 11717