Satco S11970 Manuel D'installation Et De Sécurité

LED T8 DUAL MODE
U-BEND LAMPS
Models: S11970, S11971, S11972, S11973
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING
• DANGER: Risk of shock-disconnect power before
installation.
• WARNING: Risk of fire or electric shock. The
electrical rating of these products are 120-277Vac, the
installer must determine whether they have 120-277Vac
at the luminaire before installation.
• WARNING: Risk of fire or electric shock. LED Retrofit
Kit installation requires knowledge of luminaire electrical
systems. If not qualified, do not attempt installation.
Contact a qualified electrician.
• WARNING: Product must be installed in accordance with
the national electrical code or your local electrical code.
If you are not familiar with these codes and requirements,
contact a qualified electrician.
• WARNING: Install this kit only in luminaries that have
the construction features and dimensions shown in the
photographs and/or drawing and where the input rating
of the retrofit kit does not exceed the input rating of the
luminaire.
• WARNING: To prevent wiring damage or abrasion, do
not expose wiring to edges of sheet metal or other sharp
objects.
• WARNING: To avoid potential fire or shock hazard, do
not use this retrofit kit in luminaries employing shunted
bi-pin lampholders. NOTE: Shunted lamp holders are
found only in fluorescent luminaries with instant-start
ballasts. Instant-start ballasts can be identified by the
words "Instant Start" or "I.S." marked on theballast.
Item Number-Description
S11970-13T8U6/LED/22.5-830/DUAL
S11971-13T8U6/LED/22.5-835/DUAL
S11972-13T8U6/LED/22.5-840/DUAL
S11973-13T8U6/LED/22.5-850/DUAL
INSTALLATION: DIRECT REPLACEMENT / PLUG & PLAY (TYPE A)
NOTE: This product my not be compatible with all ballasts. For more information about ballast compatibility
visit www.Satco.com.
STEP 1: Turn OFF power before installation.
STEP 2: Remove fixture diffuser (if present) and
existing fluorescent lamps from the fixture.
STEP 3: Install the LED U-bend.
STEP 4: Attach the diffuser and turn ON power.
Installation is complete.
© Copyright 2023 Satco Products, Inc. 8/23 v1.0
• WARNING: Luminaire wiring and electrical parts may be
• WARNING: Check the existing wiring for damage before
• This lamp is dimmable in Type A (Ballast Dependent)
• Suitable for damp locations.
• Not for emergency lighting.
Overall Dimensions (mm)
92 x 562.1 x 572.3
1
This designation may be in the form of a statement
pertaining to the ballast itself, or may be combinedwith
the marking for the lamps with which the ballastis intended
to be used, for example F40T 12/IS, for more information
contact the LED luminaire retrofit kit manufacturer. Do not
make or alter any open holes in an enclosure of wiring or
electrical components during kit installation. Installers should
not disconnect the existing wire from lampholder terminals
to make new connections at lampholder terminals. Instead
installers should cut existing lampholder leads away from
the lampholder and make new electrical connections to
lampholder lead wires by employing applicable connectors.
damages when installing retrofit kit hardware. Check for
enclosed wiring and components.
installing upgrade kit. Do not install if existing wires are
damaged. This retrofit kit is accepted as a component of
a luminaire where the suitability of the combination shall
be determined by authorities having jurisdiction.
Type B Lamp – this LED tube is intended to replace
fluorescent tube lamps with ANSI designation.
mode only. Dimmable ONLY with compatible dimmable
ballasts. Visit www.satco.com for compatibility list.
Operating Temperature
–20ºC ~ 45ºC
CCT Volts
3000K
3500K
120V–277V
4000K
5000K
Satco Products, Inc.
Brentwood, NY 11717