Westinghouse 042817 Guide D'utilisation

Owner's Manual
Indoor Lighting Fixture
Installation Instructions
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a
period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or
implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration
of components, nor does it cover damages caused through abuse, improper installation, surges in
electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselighting.
com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any
packing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is
essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not
damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components
are damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are
provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before
1985 have supply wires rated 60° C. Consult a qualified electrician before installing.
FIGURE 1.
*GROUND
WIRE
SIDE HOLE (P)
LOCK WASHER (F)
HEX NUT (D)
MOUNTING NIPPLE (E)
SCREW COLLAR (L)
FIXTURE LOOP (G)
CENTER PIPE (T)
NIPPLE 3 (E3)
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
W-525
meet all UL specifications.
042817
1. Turn off power at circuit box to avoid possible electric shock.
2. Secure mounting bar (A) to outlet box (B) with outlet box screws (C) (if applicable) (see fig. 1).
3. Thread hex nut (D) onto mounting nipple (E) approximately 1/4 inch and insert lock washer (F), then
thread mounting nipple (E) onto mounting bar (A) and secure hex nut (D).
4. Thread fixture loop (G) onto nipple 1 (E1).
NOTE: Do not twist or kink wires when sliding fixture loop (G) downward.
5. Open one link on bottom end of chain (J). Attach to fixture loop (G). Securely close link on chain (J).
6. Thread screw collar ring (K) onto screw collar (L), then place canopy (M) over top of screw collar (L).
7. Lace wires up through every other link on chain (J) then through screw collar (L), canopy (M), and
mounting nipple (E).
8. Open one link on top end of chain (J). Attach to loop on screw collar (L). Securely close link on chain (J).
9. Identify color coding of fixture wires (see fig. 2).
10. Connect the smooth wire with marking printed or molded from the fixture with the black wire from
outlet box (B) by wire connector (N), and wrap the wire connector (N) with electrical tape for a
more secure connection.
11. Connect the ribbed wire from the fixture with the white wire from the outlet box (B) by wire
connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
12. Partially thread green grounding screw (O) into side hole (P) on mounting bar (A) (see fig. 1).
13. Wrap grounding wire from fixture around green grounding screw stem (O) leaving enough excess
wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet
box (B) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape
for a more secure connection.
14. Tighten green grounding screw (O). Do not over tighten.
15. Tuck wires inside outlet box (B).
16. Tigthen two center pipe (T) together, then secure center pipe (T) to nipple 2 (E2) and nipple 3 (E3).
17. Attach support rods (Q) to housing rings (R) and to rings (L) on fixture.
18. Raise canopy (M) to ceiling and secure screw collar ring (K) to screw collar (L).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Install lamp(s). Do not exceed recommended wattage.
2. Turn power back on at circuit box.
FIGURE 2.
FIXTURE
WIRES:
Smooth
HOUSE
WIRES:
Black
(Hot)
*OUTLET
BOX (B)
WARNING
WIRE
Turn off electricity to the mounting site before beginning installation.
CONNECTORS (N)
Mounting instructions must be followed exactly as shown for the fixture to be safely sup-
MOUNTING BAR (A)
ported.
*OUTLET BOX
SCREWS (C)
*GREEN GROUNDING
CLEANING AND CARE
SCREW (O)
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
CANOPY (M)
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
clean this fixture.
SCREW COLLAR RING (K)
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
CHAIN (J)
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-
quer which gives maximum protection against the weather. However, in time the brightness of the
brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass fixture
NIPPLE 1 (E1)
looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-
HOUSING RING (R)
faces, giving the fixture an extra protective covering.
NIPPLE 2 (E2)
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
SUPPORT ROD (Q)
RING (S)
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
*NOT SUPPLIED
Used under license by Westinghouse Lighting.
FIXTURE FIXTURE
WIRES: WIRES:
Ribbed Bare
Copper
(Ground)
HOUSE HOUSE
WIRES: WIRES:
White Bare
(Neutral) Copper
(Ground)
www.westinghouselighting.com
All rights reserved. Made in China
Guide d'utilisation
Instructions d'installation
Appareil d' é clairage pour utilisation intérieure
GARANTIE LIMITÉE DE CINQ ANS
Cet appareil d'éclairage Westinghouse est assorti d'une garantie de 5 ans contre les défauts de
matériaux et de fabrication, qui entre en vigueur à partir de la date d'achat. La présente garantie se
substitue à toute autre garantie expresse ou tacite.
Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la
foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages
survenant suite à une utilisation anormale, une installation impropre, une surtension de courant
électrique ou des actes d'un tiers.
Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.
Si ce produit ne fonctionne pas, pour une raison quelconque couverte par cette garantie, contactez-
nous gratuitement au numéro suivant : 1-888-417-6222.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION INTÉRIEURE
Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d'éclairage a été
conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à
nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces
y sont avant de mettre l'emballage au rebut (voir fig. 1).
MISE EN GARDE: L'ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l'installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de
commencer l'installation. Un câblage approprié est essentiel au bon fonctionnement de cet
appareil d'éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur
ou un plafond, n'endommagez pas les câbles électriques, les canalisations de gaz ou d'eau. Si
l'un des composants de raccordement ou de l'appareil d'éclairage est endommagé, n'installez
pas cet appareil d'éclairage. Retournez-le à l'endroit où vous l'avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l'appareil
d'éclairage est doté d'un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se
trouvent sur l'étiquette U.L. et sur l'emballage de l'appareil d'éclairage.)
FIGURE 1.
*FIL DE MISE
A LA TERRE
TROU
LATERAL (P)
RONDELLE DE
BLOCAGE (F)
L'ECROU
HEXAGONAL (D)
MANCHON FILET
DE FIXATION (E)
COLLIER
FILETE (L)
LA BOUCLE
DE L'APPAREIL
D'ECLAIRAGE (G)
TUBE
CENTRAL (T)
Il est possible que le dessin illustré ici ne
soit pas la reproduction exacte de l'appareil
d'éclairage contenu dans la boîte.
Les instructions d'installation demeurent
cependant valables.
*BOITE DE SORTIE
DE COURANT (B)
CONNECTEURS
DE FIL (N)
BARRE DE FIXATION (A)
VIS DE LA BOITE DE
SORTIE DE COURANT (C)
*VIS DE MISE A LA
TERRE (VERTE) (O)
CHAPEAU (M)
LA BAGUE
DU COLLIER
FILETE (K)
CHAINE (J)
MANCHON
FILETE 1 (E1)
CROCHET DU
CHAPEAU (R)
MANCHON
FILETE 2 (E2)
CORDON DE
SUPPORT (Q)
BAGUE (S)
MANCHON
FILETE 3 (E3)
*NON FOURNI