Westinghouse W-417 Guide D'utilisation

Owner's Manual
LED Indoor Lighting Fixture
Installation Instructions
FIXTURE WARRANTY
This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period
of five years from purchase date. This warranty is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration
of components, nor does it cover damages caused through abuse, improver installation, surges in
electric current, or acts of third parties.
This warranty does not cover the costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, please contact us at www.westinghouse-
lighting.com/contact-us.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselighting.
com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-
ing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-
tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-
age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provid-
ed on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985
have supply wires rated 60° C. Consult a qualified electrician before installing.
FIGURE 1.
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
*OUTLET
BOX (B)
*GROUND
WIRE (A)
SIDE
HOLE (F)
GREEN
GROUNDING
SCREW (E)
CORD LOCK (L)
SET SCREW (H)
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
W-417
meet all UL specifications.
062820
1. Turn off power at circuit box to avoid possible electric shock.
2. Identify color coding of fixture wires (see fig.2).
3. Connect the black wire from the fixture with the black wire (live wire) from the outlet box (B) by wire
connector (D), and wrap the wire connector (D) with electrical tape for a more secure connection.
4. Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box (B) by
wire connector (D), and wrap the wire connector (D) with electrical tape for a more secure connection.
5. Partially thread green grounding screw (E) into side hole (F) on mounting plate (C) (see fig.2).
6. Wrap the bare grounding wire (A) from the fixture canopy (G) around the green grounding screw (E)
on the mounting plate (C) leaving enough excess wire. Connect the greenish grounding wires (A)
from hanging cord and excess grounding wire from the fixture canopy (G) with the grounding wire
from outlet box (B) by using a wire connector (D), then wrap the wire connector (D) with electrical
tape for a more secure connection.
7. Tighten green grounding screw (E). Do not over tighten.
8. Tuck wires inside outlet box (B).
9. Raise mounting plate (C) upto outlet box (B), secure with outlet box screws (N) (included).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Raise canopy (G) up to mounting plate (C), secure with set screws (H).
2. Raise decorative net (J) up to fixture shade (I), secure with clips on decorative net (J).
3. Turn power back on at circuit box.
ADJUSTING LENGTH OF CORD
These steps should only be performed by someone familiar with working with electrical wiring. Care
must be taken when adjusting the length of the cord to ensure insulation on internal wires is not
damaged. If not familiar with these steps, seek the aid of a qualified electrician.
1. Remove Wire Connectors (M) connecting end of cord to wires from the Mounting Plate (C). Note
which color wires are connected in each Connector.
2. Loosen the screw in strain relief (K) until cord slides easily, being careful not to completely remove
screw. Slide canopy down cord until the fixture is the correct distance below the canopy. Tighten
the screw in the strain relief until cord does not slide.
3. Slide cord through one side of Cord Lock (L) until Cord Lock is nearly touching the top of the strain
relief (K). Slide cord through the other side of the cord lock until it locks in place.
4. Cut cord approximately two to three inches (2"-3") above Cord Lock.
5. Leaving at least one inch (1") of outer insulation above the Cord Lock, carefully cut through outer
insulation of cord, being careful not to damage inner insulation. Remove outer insulation. Strip
inner insulation from end of both wires, leaving approximately 1/2 inch of wire exposed.
6. Attach new cord ends to the wires from the box attached to the Mounting Plate (C), using Wire
Connectors (M) removed earlier, matching colors as previously noted. Tape Connectors for more
secure connection.
FIGURE 2.
FIXTURE
WIRES:
Black
WIRE
CONNECTORS (D)
MOUNTING WARNING
PLATE (C)
Turn off electricity to the mounting site before beginning installation.
*OUTLET BOX
SCREWS (N)
Mounting instructions must be followed exactly as shown for the fixture to be safely supported.
WIRE
CONNECTORS (M)
CANOPY (G)
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
STRAIN RELIEF (K)
clean this fixture.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
SHADE (I)
DECORATIVE
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
NET (J)
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
*NOT SUPPLIED
Used under license by Westinghouse Lighting.
FIXTURE FIXTURE
WIRES:
WIRES:
White
Bare
Copper
(Ground)
HOUSE HOUSE HOUSE
WIRES: WIRES:
WIRES:
Black White
Bare
(Hot) (Neutral)
Copper
(Ground)
www.westinghouselighting.com
All rights reserved.
Guide d'utilisation
Appareil d' é clairage pour utilisation intérieure avec DEL
GARANTIE LIMITÉE DE CINQ ANS
Ce luminaire Westinghouse est garanti pièces et main-d'oeuvre pour une période de Cinq ans à compter
de la date d'achat. Cette garantie remplace toute autre garantie, explicite ou implicite.
Cette garantie ne couvre pas les phénomènes naturels comme les dommages de la foudre, ni la corro-
sion ou la décoloration des composants, pas plus qu'elle ne couvre les dommages causés par les abus,
une installation inappropriée, les surtensions électriques ou les actes de tiers.
Cette garantie ne couvre pas les coûts de dépose et de pose du luminaire.
En cas de défaillance du produit, pour une raison quelconque, couverte par cette garantie, veuillez
nous contacter via www.westinghouselighting.com/contact-us.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION INTÉRIEURE
Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d'éclairage a été
conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à
nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces
y sont avant de mettre l'emballage au rebut (voir fig. 1).
MISE EN GARDE: L'ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l'installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de com-
mencer l'installation. Un câblage approprié est essentiel au bon fonctionnement de cet appareil
d'éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur ou un
plafond, n'endommagez pas les câbles électriques, les canalisations de gaz ou d'eau. Si l'un des
composants de raccordement ou de l'appareil d'éclairage est endommagé, n'installez pas cet
appareil d'éclairage. Retournez-le à l'endroit où vous l'avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l'appareil
d'éclairage est doté d'un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se
trouvent sur l'étiquette U.L. et sur l'emballage de l'appareil d'éclairage.)
FIGURE 1.
Il est possible que le dessin illustré ici ne soit pas la reproduction exacte de l'appareil
d'éclairage contenu dans la boîte.
Les instructions d'installation demeurent cependant valables.
*FIL DE MISE
TROU
LATERAL (F)
VIS DE MISE
A LA TERRE
(VERTE) (E)
DISPOSITIF DE
BLOCAGE DU
CORDON (L)
VIS DE
CALAGE (H)
Made in China
Instructions d'installation
*BOITE DE SORTIE
DE COURANT (B)
CONNECTEURS
A LA TERRE (A)
DE FIL (D)
PLAQUE DE
MONTAGE (C)
*VIS DE LA BOITE DE
SORTIE DE COURANT (N)
CONNECTEURS (M)
CHAPEAU (G)
SERRE-CÂBLE (K)
ABAT-JOUR (I)
FILET
DÉCORATIF (J)
*NON FOURNI