CHROMATEQ CLUB-E 1024 Guide De Démarrage Rapide

ENG Quick start Guide - CLUB-E 1024
This quick start guide contains important informations on the safe operation of the product.
Read and follow the safety advice and instructions given. Retain the quick start guide for future reference.
If you pass the product on to others please include this quick start guide.
Safety instruction
Intended use:
This device is intended to control lighting devices and
effects via computer using appropriate software. Any
other use or use under other operating conditions is
considered to be improper and may result in personal
injury or property damage. No liability will be assumed
for damages resulting from improper use.
General handling:
• Never use force when handling the product
• Never immerse the product in water
• Just wipe it with a clean dry cloth.
• Do not use liquid cleaners such as benzene,
thinners or flammable cleaning agents
Features
Hardware features:
• Input : USB-C RJ45 Ethernet LAN (10mb/s)
• DMX Outputs : 1024 (2x512) on 3 pin XLR, Live PC and Stand Alone
• Max interface connected : 12 by USB / 128 by Ethernet
• NODE, Art-Net & sACN to DMX decoder : 2x512 out per interface
• DMX mode : DMX In/Out, DMX Splitter, DMX Record, DMX Trigger
• Wi-Light 2 APP command and configuration : LAN
Remote triggers, requires a WIFI router
• Internal Memory : Yes (65 KB)
• Memory Capacity : 60 memory steps for 1024 ch.
• Infrared (scenes, play, pause, dimmer, speed) Remote
Front Panel
2 1 2 1
3 3
 
Rear Panel





Never use the product:
• In direct sunlight
• In conditions of extreme temperature or humidity
• In extremely dusty or dirty areas
• At locations where the unit can become wet
• Near magnetic fields
Danger for children:
Ensure that plastic bags, packaging... are
disposed of properly and are not within
reach of babies and young children. Choking
Choking
hazard! Ensure that children do not detach
hazard!
any small parts from the product. They could
swallow the pieces and choke!
Unit is Optional)
• Button : Next scene or mode selection (hold 5s.)
• UDP Ethernet triggers and commands (SDK) : requires
a WIFI router
• Power input : 5V DC, 0.3 A via USB-C
• Housing : Diecast / Extruded Aluminum with brushed
anodized finish
• Dimensions : H: 90 (3.54), W: 80 (3.15), D: 45 (1.77)
• Operating Temperature : -40 to +85 C° / -40 to 185 F°
• International Warranty : 5 years
Front Panel

XLR Connector 3 pins
Output DMX A,
1: Ground
2: Data -

3: Data +
Input / Output DMX B
Rear Panel
 
RJ45, Network (LAN) Next scene in Stand
connection Alone mode
Modes selector (5 s.)

Stand Alone mode; NODE
USB-C, power connector
Art-Net or NODE sACN
(5V. DC, 0.3A)


LEDs signals : green (G)
Infra-red receiver
and Yellow (Y)
LED, Infrared remote: Not
included, optional
USB Signal LED operating states
G off + Y off Interface not powered
G on + Y off Interface powered, No scene is playing
G fast blink + Y off USB communication running with the software
G on + Y fast blink Ethernet communication running
G slow blink + Y off Stand Alone mode and playing a scene from memory
G on + Y slow blink x1 NODE Mode converter Art-Net to DMX
G on + Y slow blink x2 NODE Mode converter sACN to DMX
G + Y fast blink In bootloader mode, waiting to load a new firmware
DMX Wiring - Live mode (USB)
Ethernet connection and configuration
(software options or DEVICETOOL)
• DHCP is Default mode: IP address is
assigned automatically by the DHCP server
(IP Switch or Wifi router)
• Static IP mode: The IP address is fixed by
the user. The IP address won't change.
Default IP address: 192.168.0.5
Default Subnet mask: 255.255.255.0
Ethernet connection mode :
Setup an identical IP address
range like 192.168.0.x. and setup an
identical subnet mask to 255.255.255.0 to
the device and computer.
NODE Art-Net mode :
With the Device tool or the software.
Programming the device and DMX Playback - StandAlone mode
Setup the "Short Name" and the "Long Name".
• Download and install the free lighting control software and USB drivers.
Choose the DMX ports or outputs
• Connect your device to your computer via the included USB-C cable.
of the Node by modifying the "SubNet"
• Start the software (your interface will be detected automatically).
and "DMX Universe".
• Configure the software according your DMX lighting fixture setting.
Then apply the modifications.
• Program scenes and sequences using the lighting control software.
NODE sACN mode : • Play your show in live mode.
Setup and choose the DMX universes. • To play in standalone mode, save the programmed scenes and sequences into
Then applied the internal memory.
• Close the software. Your panel is now ready to operate in standalone mode.
Always restart the device after IP or
mode configuration: unplug it from the
power supply
Caution: Check the contents of the package and the condition of the interface after unpacking! Contact your supplier
if something is missing or is damaged. Do not use the device if it appears to be damaged!
Technical support, Free Software and Application :
Technical support : https://chromateq.com/contact-form/
Software download : https://chromateq.com/dmx-software-downloads/
System Requirements:
• Windows ©, Mac OS ©, Linux © (32/64 bits)
• 2Ghz CPU (2 cores), 8 Gb RAM
• 2Gb RAM graphic card (for 3D only)
• 600 Mb disk, 1920x1080 screen resolution
• 1 USB & Ethernet Port (for Art-Net & sACN)
DMX Wiring - Standalone mode
DMX Wiring - Live mode Ethernet, NODE Art-Net / sACN mode
CHROMATEQ SARL
191 allée de Lauzard - Bat.B, Rdc 1
34980 Saint Gely du Fesc - FRANCE
Phone : +33 (0) 952210755 (France) / +86 20 22889704 (China)
Mobile : +33 651509358 (France) / +86 13422062209 (China)
eMail : info@chromateq.com
Copyright © 2024 - CHROMATEQ.All rights reserved.