Télécharger Imprimer la page

Celduc okpac SO943460 Mode D'emploi page 3

Publicité

Fig. 2 Courbes thermiques & Choix dissipateur thermique /
60
50
40
30
20
10
0
0
0
0
5
Courant de charge / RMS load current (A)
12K/W correspond à un relais sans dissipateur monté dans l'air /
6K/W correspond à un relais monté sur un adaptateur DIN celduc type 1LD12020
6K/W corresponds to a relay mounted on a DIN rail adaptator like celduc 1LD12020
1 -Itsm non répétitif
sans tension réappliquée est
donné pour la détermination des protections.
1 -
No repetitive Itsm
is given without voltage
reapplied . This curve is used to define the
protection (fuses).
2 -Itsm répétitif
est donné pour des surcharges de
courant (Tj initiale=70°C).
Attention : la répétition de ces surcharges de courant
diminue la durée de vie du relais.
2 -
Repetitive Itsm
is given for inrush current with
initial Tj = 70 ° C. In normal operation , this curve
musn't be exceeded.
Be careful, the repetition of the surge current
decreases the life expectancy of the SSR.
−>
Attention ! les relais à semi-conducteurs ne procurent pas d'isolation galvanique entre le réseau et la charge. Ils doivent être utilisés
associés à un disjoncteur avec propriété de sectionnement ou similaire, afin d'assurer un sectionnement fiable en amont de la ligne dans
l'hypothèse d'une défaillance et pour tous les cas où le relais doit être isolé du réseau (maintenance ; non utilisation sur une longue durée...).
−>
Warning ! semiconductor relays don't provide any galvanic insulation between the load and the mains. Always use in conjunction
with an adapted circuit breaker with isolation feature or a similar device in order to ensure a reliable insulation in the event of wrong
function and when the relay must be insulated from the mains (maintenance ; if not used for a long duration ...).
Rue Ampère B.P. 4
Fax +33 (0) 4 77 53 85 51
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21
okpac 
Full on State
50% on State
10 15 20 25 30 35 40
fig 3 : Courants de surcharges /
42290 SORBIERS - FRANCE
Thermal curves and heatsink choice
1,1K/W
1,5K/W
2,1K/W
4K/W
6K/W
12K/W
0 10 20 30 40 50 60 70 80 90 100
0
Température ambiante / Ambient temperature (°C)
12K/W corresponds to a relay without heatsink .
Overload currents
Surcharge de courant : Itsm(Apeak) = f(t) pour modèle 35A (Itsm=400A)
Surge current : Itsm (Apeak) =f(t) for 35A models with Itsm=400A
4 0 0
3 5 0
3 0 0
2 5 0
2 0 0
1 5 0
1 0 0
5 0
0 , 0 1
celduc
r
e
l
a
i
s
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
S/MON/SO943460/A/29/06/2004
0,75K/W
2
0 , 1
1
Time (s)
E-Mail : celduc-relais@celduc.com
Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19
page 3 / 5F/GB
60
50
40
30
20
10
0
0
1
1 0
www.celduc.com

Publicité

loading