Publicité
Liens rapides
Remote control compatible receiver Cebek issuers TL-5, TL-6, TL-11, TL-12, TL-13, TL-14, TL-15 and TL-16.
Includes micro code selection, antenna output indicator LEDs and connection terminals.
POWER SUPPLY: 230V AC . Install a fuse and a switch to the protection and safety, as reflected in the CE standard.
OPERATION: First, is the security code setting. All remotes Cebek approved work at frequency 433.92 MHz therefore
incorporate battery micro-switches, INT-0, which allow you to configure custom security code for each command.
Have up to 13,122 different combinations to code your remote.
In the drawing corresponding to the micro-switches battery INT-0, check the availability of 8 switches, each of which
could be placed in three different positions, - / 0 /. Change comes standard provision modifying switches. Note that for
there to be communication with the receiver, you must set this to the same code that is used in the transmitter
After setting the sender and the receiver with the desired code, activate the power. Then press the transmitter button,
the corresponding output will turn on and remain in this state until you bind the issuer, at which output disconnect.
Télécommande compatible récepteur Cebek émetteurs TL-5 TL-6, TL-11, TL-12, TL-13, TL-14, TL-15 et TL-16.
Comprend sélection de code micro, antenne voyants lumineux de sortie et les bornes de connexion.
ALIMENTATION: 230V AC. Installez un fusible et un interrupteur pour la protection et la sécurité, comme en témoigne
la norme CE.
OPERATION: d'abord, c'est le réglage du code de sécurité. Toutes les télécommandes Cebek approuvé les travaux à
la fréquence 433.92 MHz donc intégrer des micro-interrupteurs de batterie, RC-0, qui vous permettent de configurer le
code de sécurité personnalisé pour chaque commande.
Avoir jusqu'à 13 122 combinaisons différentes de coder votre télécommande.
Bistable receiver Remote
Bistable récepteur à distance
Telemando receptor biestable
Telecomandament receptor biestable
www.cebek.com
-
1 channel
TL-9
TECHNICAL CHARACTERISTIC
Supply voltage : 230VAC
minimum consumption : 2W
Maximal consumption : 3W
Working frequency : 433,92 Mhz
Max. for output : 3A.
Measures : 109x72x28 mm.
Weight : 64 gr.
Din rail : C-7568
sat@fadisel.com
Publicité
Manuels Connexes pour CEBEK TL-9
Sommaire des Matières pour CEBEK TL-9
- Page 1 POWER SUPPLY: 230V AC . Install a fuse and a switch to the protection and safety, as reflected in the CE standard. OPERATION: First, is the security code setting. All remotes Cebek approved work at frequency 433.92 MHz therefore incorporate battery micro-switches, INT-0, which allow you to configure custom security code for each command.
- Page 2 FUNCIONAMIENTO : Primero, ha de realizarse la configuración del código de seguridad. Todos los telemandos Cebek trabajan en la frecuencia homologada de 433.92 MHz. Por ello, incorporan una batería de micro-switches, INT-0, que permiten configurar un código de seguridad personalizado para cada mando.
- Page 3 "JP" JP-1 jumper and leave it in the open state. Remember that for the TL-9 can work with the issuer of a JP-1 channel should be closed.
- Page 4 TL-9 OUTPUT connection. LOAD: The output is via a relay device that supports any type of load does not exceed 3A .. The relay has three output terminals. The rest normally open (NO), the normally closed (NC) and the Joint Operation of this mechanism is identical to a switch whose two terminals NA and Common To obtain the reverse should be used NC and Common terminals the figure shows the typical connection for devices operating at 12V.
- Page 5 TL-9 www.cebek.com sat@fadisel.com...