Publicité
English
Top and front panels (See 1)
1 VOLUME - to adjust volume level
2 Source selector : CD,TUNER,
TAPE/
POWER OFF
- selects CD, tuner or tape source of sound
- power off switch
3 CD door
4 TUNING - tunes to radio stations
5 BAND - selects waveband
6 PREVIOUS, NEXT ∞ , §
- skips or searches a passage/track
backwards or forward
7 PROG - programs and reviews
programmed track numbers
8 CASSETTE RECORDER keys:
; - pauses playback or recording
9/ - stops the tape;
- opens the cassette holder
5 or 6 - fast rewinds/ winds tape
2 - starts playback
0 - starts recording
9 Cassette door
0 CD Display - shows the CD functions
! PLAY/PAUSE 2; - starts or pauses CD
playback.
@ STOP 9 - stop playback;
- erases a CD program.
Back panel
# Telescopic antenna - improves FM
reception.
Note: AM band antenna is built into set
(see Tuner reception)
Controls/Power Supply
$ Battery door - open to insert 6 x 1.5V
R-14/ UM2/ C-cells.
% AC POWER/MAINS - inlet for power
cord.
^ Voltage selector - (inside the battery com-
partment, not all versions) adjust to match
the local voltage 110/220V before plugging in
the set.
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
Power Supply
Whenever convenient, use the mains supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1 Open the battery compartment and insert
six batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity
as indicated by the "+" and "- " symbols inside
the compartment. (See 1)
2 Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.
Batteries contain chemical substances, so
they should be disposed of properly.
Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst:
Power Supply
•
Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
•
When inserting new batteries, do not try to
mix old batteries with the new ones.
•
Remove the batteries if the set is not to be
used for a long time.
Using AC Mains
1 Check if the power/mains voltage, as shown
on the type plate located on the
bottom of the set, corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2 Connect the power cord to the AC
POWER/MAINS inlet and the wall socket.The
mains lead is now connected and ready for
use.
3 To switch the set off completely, withdraw the
power cord from the wall socket.
•
Disconnect the mains lead from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the bottom
of the set.
Switching POWER on/off:
Save energy
To avoid unnecessary energy consumption,
always adjust the source selector to
TAPE/
after using the set. Also
POWER OFF
check that the tape deck keys are released.
General operation
1 To select your sound source adjust the
source selector to : CD, TUNER or
TAPE/
.
POWER OFF
Tuner/CD Player
2 Adjust the sound with the VOLUME control.
3 To switch off the set, adjust the source
selector to TAPE/
position and
POWER OFF
check the cassette keys are released.
Tuner reception
1 Adjust the source selector to TUNER.
2 Adjust BAND to select your desired wave-
band.
3 Turn TUNING to tune to a station.
•
For FM band signals, extend and turn the
telescopic antenna for best reception. Reduce
its length if the signal is too strong.
•
For MW (AM) band signals, the set uses a
built-in antenna. Direct this antenna for best
reception by turning the whole set.
4 To switch off the radio, adjust the source
selector to TAPE/
position and
POWER OFF
check the cassette keys are released.
CD Player
Display indication for CD functions:
- OP: (See 2) CD door open
- --: (See 3) reading disc contents / no
disc/ error in CD operation or CD/ CD-
R is blank or not finalized (see
Troubleshooting)
- During CD playback: 2 and current
track number
- 2;: (See 4) playback on pause
- prog: when CD program is active
- Fu: program memory full
Playing a CD
This CD player plays Audio Discs
including CD-Recordables.
Publicité
