Publicité
Les langues disponibles
Les langues disponibles
3.9
Read, understand and follow all instructions for the charger, battery, vehicle
and any equipment used near the battery and charger. Study all of the bat-
tery manufacturer's specific precautions while charging and recommended
rates of charge.
3.10
Determine the voltage of the battery by referring to the vehicle owner's
manual and make sure that the output voltage of the charger is the correct
voltage.
3.11
Make sure that the charger cable clips make tight connections.
4.
CHARGER LOCATION
4.1
Locate the charger as far away from the battery as the DC cables permit.
4.2
Never place the charger directly above the battery being charged; gases
from the battery will corrode and damage the charger.
4.3
Do not set the battery on top of the charger.
4.4
Never allow battery acid to drip onto the charger when reading the electro-
lyte specific gravity or filling the battery.
4.5
Do not operate the charger in a closed-in area or restrict the ventilation in
any way.
5.
DC CONNECTION PRECAUTIONS
5.1
Connect and disconnect the DC output clips only after setting all of the
charger switches to the "off" position and removing the AC plug from the
electrical outlet. Never allow the clips to touch each other.
5.2
Attach the clips to the battery and chassis, as indicated in steps 6.5, 6.6,
7.2, 7.3 and 7.4.
6.
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN
VEHICLE.
6.1
Position the AC and DC cables to reduce the risk of damage by the hood,
door and moving or hot engine parts. NOTE: If it is necessary to close the
hood during the charging process, ensure that the hood does not touch the
metal part of the battery clips or cut the insulation of the cables.
6.2
Stay clear of fan blades, belts, pulleys and other parts that can cause injury.
6.3
Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery
post usually has a larger diameter then the NEGATIVE (NEG, N, -) post.
6.4
Determine which post of the battery is grounded (connected) to the chassis.
If the negative post is grounded to the chassis (as in most vehicles), see
step 6.5. If the positive post is grounded to the chassis, see step 6.6.
6.5
For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the
battery charger to the POSITIVE (POS, P, +) ungrounded post of the battery.
Connect the NEGATIVE (BLACK) clip to the vehicle chassis or engine block
away from the battery. Do not connect the clip to the carburetor, fuel lines or
sheet-metal body parts. Connect to a heavy gauge metal part of the frame
or engine block.
6.6
For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from
the battery charger to the NEGATIVE (NEG, N, -) ungrounded post of the
battery. Connect the POSITIVE (RED) clip to the vehicle chassis or engine
block away from the battery. Do not connect the clip to the carburetor, fuel
lines or sheet-metal body parts. Connect to a heavy gauge metal part of the
frame or engine block.
6.7
When disconnecting the charger, turn all switches to off, disconnect the AC
cord, remove the clip from the vehicle chassis and then remove the clip from
the battery terminal.
6.8
See CALCULATING CHARGE TIME for length of charge information.
7.
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE
VEHICLE.
7.1
Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery
post usually has a larger diameter than the NEGATIVE (NEG, N, -) post.
7.2
Attach at least a 24-inch (61 cm) long 6-gauge (AWG) insulated battery
cable to the NEGATIVE (NEG, N, -) battery post.
7.3
Connect the POSITIVE (RED) charger clip to the POSITIVE (POS, P, +)
post of the battery.
All manuals and user guides at all-guides.com
Risk of explosion and contact with
battery acid.
A spark near the battery may cause
a battery explosion. To reduce the
risk of a spark near the battery:
A spark near the battery may cause
a battery explosion. To reduce the
risk of a spark near the battery:
7.4
Position yourself and the free end of the cable you previously attached to
the NEGATIVE (NEG, N, -) battery post as far away from the battery as pos-
sible – then connect the NEGATIVE (BLACK) charger clip to the free end of
the cable.
7.5
Do not face the battery when making the final connection.
7.6
When disconnecting the charger, always do so in the reverse order of the
connecting procedure and break the first connection while as far away from
the battery as practical.
7.7
A marine (boat) battery must be removed and charged on shore. To charge
it onboard requires equipment specially designed for marine use.
8.
BATTERY CHARGING – AC CONNECTIONS
Risk of electric shock or fire.
8.1
This battery charger is for use on a nominal 120-volt circuit. The charger
must be grounded to reduce the risk of electric shock. The plug must be
plugged into an outlet that is properly installed and grounded in accordance
with all local codes and ordinances. The plug pins must fit the receptacle
(outlet). Do not use with an ungrounded system.
8.2
Never alter AC cord or plug provided – if it does not fit the outlet, have
proper grounded outlet installed by a qualified electrician. Improper connec-
tion can result in a risk of an electric shock or electrocution. NOTE: The use
of an adapter plug is not recommended.
8.3
Recommended minimum AWG size for extension cord:
•
100 feet long or less - use an 18 gauge extension cord.
•
Over 100 feet long - use a 16 gauge extension cord.
9.
FEATURES
7
1.
Microprocessor Controlled
2.
Automatic Voltage Detection
3.
CONNECTED
4.
CHARGING
5.
CHARGED
6.
Reverse Connection Protection
7.
Battery Clip Cable Assembly
8.
Ring Terminal Cable Assembly
9.
Automatic Temperature Compensation
10.
ASSEMBLY INSTRUCTIONS
No assembly required
11.
CONTROL PANEL
LED Indicators
CONNECTED
(red) LED lit: Indicates that there is AC power supplied to
the battery charger.
CHARGING
(yellow) LED lit: Indicates the charger is charging the
battery.
CHARGING
(yellow) LED flashing: Indicates the charger is in abort
mode.
CHARGED
(green) LED lit: Indicates the battery is fully charged and the
charger is in maintain mode.
NOTE: See the Operating Instructions section for a complete description of the
charger modes.
2
8
5
4
3
(red) LED
(yellow) LED
(green) LED
Publicité
