Satco NUVO S28928 Instructions D'installation

HI-PRO LED WALL PACK LAMPS
Models: S28928, S28929, S28930, S28980, S28987
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING:
Risk of Fire or Electric Shock
• Please read this manual carefully before use. Make sure the application is in accordance with the
instructions before use.
• Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit.
Check for enclosed wiring and components.
• To reduce the risk of electric shock and fire, this lamp must be installed, tested and maintained by
professionals using special equipment.
• Do not operate lamps on existing ballasts. These LED lamps require all the ballasts, capacitors, and
ignitors to be bypassed or removed.
• Suitable for dry and damp locations. Do not use where directly exposed to water.
• Wattage selectable light level switching.
• Added weight of the device may cause instability of a free-standing portable luminaire.
• This device is not intended for use with emergency exits.
• Install this kit only in luminaires that have the construction features and dimensions shown in the photographs
and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• When using in portable table luminaires, ensure the distance from the bottom of the base to the top of the
lampholder does not exceed three (3) times the base diameter.
• Before installation make certain the AC power to the fixture is off.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead installers
should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires by employing
applicable connectors.
• For use in enclosed fixtures.
Item # Watts
S28928 20-10-5W
S28929 40-30-20W
S28930 40-30-20W
S28980 30-20-10W
S28987 60-40-20W
INSTALLATION
Each lamp can be set to the desired color temperature and wattage during the installation process.
NOTE: Before installation, select the Wattage and Color Temperature (CCT) by sliding the switch, 3000K left, 4000K middle,
5000K right. See STEP 3.
1
STEP 1: Turn off the power before installation.
Remove the old ballast, capacitor and ignitor
(if existing). See Figure 1.
4
STEP 4: Screw the LED lamp onto the
corresponding socket. See Figure 4.
Securely fasten the earth fly lead cable to the
main body structure. If cable is damaged,
DO NOT USE. Replace with 1.0mm cable
and insulate from heat.
© Copyright 2023 Satco Products, Inc. 5/23
* (See step 3 below - Do not use with conventional dimmers)
Volts (VAC) Base
E26
E26
EX39
100 – 277V
E26
EX39
2
STEP 2: Make sure the Alternating Current
Wires connect to the E39, EX39, and E26
socket directly. Reattach or replace ground
lead if one is needed. See Figure 2.
5
Dimensions (Inches) Min. Compartment
5.43" Length, ø 3.62"
7.8" Length, ø 3.62"
8.43" Length, ø 3.62"
7" Length, ø 3.62"
(L) 200mm/7.88" x
10.59" Length, ø 3.62"
(W) 200mm/7.88"
Color temperature
(CCT) selection switch
Operating Temperature
Totally enclosed fixtures:
N/A
–22ºF to 113ºF (–30ºC to 45ºC)
Open fixtures:
–22ºF to 140ºF (–30ºC to 60ºC)
3
INSTALLATION USING
SUPPORT STAND
For installation in downward horizontal
fixture, use support with double
"prongs." Cut to desired length after
installation. See Figure 5.
Satco Products, Inc.
Brentwood, NY 11717
STEP 3:
*Set the wattage
selectable light
level switch
(on top of lamp).
Select color
temperature.