Publicité
Liens rapides
BASO 1.5 LOUVER SURFACE
MOUNTING INSTRUCTIONS
DO NOT DISCARD!
BASO 1.5 DIRECT SURFACE
38.1mm
1 ½"
42.9mm
1
"
XAL Inc. 150 Hawley Rd. Oxford, CT 06478 T: +1 203.292.9990 www.xalusa.com
MOUNTING
POSITION
FEEDER
3"
/
POSITION
2"
/
50.8mm
L 48"
MOUNTING
POSITION
FEEDER
3"
/
POSITION
2"
/
50.8mm
MOUNTING
POSITION
FEEDER
3"
/
POSITION
2"
/
50.8mm
Please see next pages for suspended version
SIGN LEGEND
POWER OFF
POWER ON
DON´T TOUCH
THE LED
ATTENTION
USE ESD
GLOVES
ENDCAP
76.2mm
WIDTH
"
/
1219.2mm
MOUNTING POSITION
L / ½ = 48"
ENDCAP WIDTH
76.2mm
L 72"
/
1828.8mm
MOUNTING POSITION
L / ½ = 48"
76.2mm
L 96"
/
2438.4mm
TOOLS REQUIRED
(not included)
PENCIL
SCREWDRIVER
SCREWS
DRILL
BRACERS
(for appropriate
application)
/
4.8mm
/
1219.2mm
"
/
4.8mm
/
1219.2mm
ENDCAP WIDTH
"
/
4.8mm
MI-V02
03/2022
1
Publicité
Manuels Connexes pour XAL BASO 1.5 LOUVER
Sommaire des Matières pour XAL BASO 1.5 LOUVER
- Page 1 L 72" 1828.8mm MOUNTING POSITION L / ½ = 48" 1219.2mm MOUNTING POSITION FEEDER ENDCAP WIDTH 3" 76.2mm POSITION " 4.8mm 2" 50.8mm L 96" 2438.4mm XAL Inc. 150 Hawley Rd. Oxford, CT 06478 T: +1 203.292.9990 www.xalusa.com MI-V02 03/2022...
- Page 2 11. Make primary connection to feeder 12. Make connection between segments 13. Test the grounding of the channel(s) *MAX 0.5 OHM RESISTANCE* XAL Inc. 150 Hawley Rd. Oxford, CT 06478 T: +1 203.292.9990 www.xalusa.com MI-V02 03/2022...
- Page 3 6. LEDs are high-quality electronic components! Please avoid touching by hand the LED light emitting surface while assemblying or replacing parts and during maintenance work. The LED circuit must always be closed, before the converter is connected to the main power. XAL does not assume any liability for damages resulting from nonobservance of this rule.
- Page 4 L / ½ = 48" 1219.2mm feeder/suspension L 78" / 1981.2mm " " L 96" 81mm 81mm 2438.4mm endcap width 3 ⅜" 3 ⅜" "/ 4.8mm 85.9mm 85.9mm XAL Inc. 150 Hawley Rd. Oxford, CT 06478 T: +1 203.292.9990 www.xalusa.com MI-V02 03/2022...
- Page 5 5. Use screws to secure strain relief through cover plate through bracket 6. Connect wiring to power source 7. Place bracket into junction box 8. Screw bracket into junction box XAL Inc. 150 Hawley Rd. Oxford, CT 06478 T: +1 203.292.9990 www.xalusa.com MI-V02 03/2022...
- Page 6 21. SYSTEMS: Apply black electrical tape 20. SYSTEMS: Slide channels to the interior of the channels together. Secure connectors with screw and nut (where channels meet) XAL Inc. 150 Hawley Rd. Oxford, CT 06478 T: +1 203.292.9990 www.xalusa.com MI-V02 03/2022...
- Page 7 6. LEDs are high-quality electronic components! Please avoid touching by hand the LED light emitting surface while assemblying or replacing parts and during maintenance work. The LED circuit must always be closed, before the converter is connected to the main power. XAL does not assume any liability for damages resulting from nonobservance of this rule.