Numark NDX900 Guide D'utilisation Rapide page 6

Masquer les pouces Voir aussi pour NDX900:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

14.
PITCH / KEYLOCK – The pitch button controls the range of the pitch fader as well as enabling and disabling key lock
mode.
Press and release the pitch button to cycle through pitch fader settings of +/- 6%, 12%, 25% and 100%. You can also
disable the pitch fader by pressing the pitch button again after selecting 100%.
The other function of this button is key lock. To engage key lock mode, hold the pitch button for two seconds. This
feature allows you to change the speed of the song without changing the key. The key of the song will lock to whatever
position the pitch fader is at when key lock is engaged.
To change the key of a song manually, hold PITCH / KEYLOCK and turn the PARAMETER knob.
15.
PITCH FADER – This controls the speed of the music. Moving towards the "+" will speed the music up, while moving
towards the "-" will slow it down. The percentage of pitch adjustment is shown on the display.
16.
PITCH BEND – Allows you to briefly adjust the speed of the music faster or slower for as long as the button is held.
Useful for quick speed adjustments to help match the beats of two songs that might be at the same tempo but have
beats that hit at slightly different times.
17.
BLEEP / REVERSE SWITCH – Use this if you want to play a CD backwards. "Bleep" mode will play the music in
reverse while the CD timer continues to advance. When you release the switch, the CD will continue to play where it
would have been if you had not engaged the switch. "Reverse" mode will play music in reverse and the CD time will also
count backwards.
18.
LOOP IN / OUT / RELOOP – These buttons are used to define your beginning and ending loop points (LOOP IN and
LOOP OUT) or to replay or restart your loop (RELOOP). For more information about this feature please see the looping
section of this manual.
19.
TRIGGER BUTTONS – These buttons can be used for 3 possible functions, chosen by holding the REC button and
turning the PARAMETER knob. For more information see the "Multi Mode Trigger Buttons" section later in this manual.
20.
SHIFT – Used with the looping feature, the shift switch allows you to cut your loop in half or double it.
21.
REC – This button is used in conjunction with the 3 assignable TRIGGER BUTTONS to record samples and set hot start
points. When used in conjunction with the parameter knob, this allows you to set the mode for the three multi-mode
trigger buttons.
To choose a mode, hold the REC button, then while continuing to hold REC, hold the desired TRIGGER BUTTON and
turn the PARAMETER knob to select the option you want to change. For more information see the "Multi Mode Trigger
Buttons" section later in this manual.
22.
(BUTTON) MODE – This button is used to change the function of the 3 assignable buttons. Pressing this button will
cycle between LOOP-2, HOT CUE and SAMPLES. For more information see the "Multi Mode Trigger Buttons" section
later in this manual.
23.
FX – Pressing this button will turn effect mode on or off. If the button is illuminated, effects mode is on.
24.
FX SELECT – Use this toggle switch to choose which effect you want to use. There are six different effects available.
See the effects section in this manual for more information.
25.
WET / DRY FADER – Use this to adjust how much of the effect will be mixed into the main mix. The 0% or "dry" side of
the fader will give you less of the effected music and more of the original music while the 100% or "wet" side adds more
of the effected music and less of the original music.
26.
PARAMETER – This knob has multiple uses depending on what you are doing when you turn it.
By default, spinning this knob will adjust a parameter of the effect you have currently chosen with the FX SELECT
switch. For more information see the effect section later in this manual.
Other settings can be adjusted by holding down an appropriate button while turning the PARAMETER knob.
27.
PROG (Program) – This button helps you create a program – a sequence of tracks to play continuously. To create a
program, press PROGRAM when the CD player is paused. To enter a track into the program, use the TRACK KNOB to
select the desired track then press PROGRAM to enter it. Repeat this process for each track you want to enter (in the
order you want them to play). When you have finished, press PLAY to start playing the program. The tracks will play in
the order you entered them. To cancel your program as it is playing, press and hold PROGRAM for three seconds.
Holding down the PROG button and turning the PARAMETER knob will bring you to a list of menu options. Please see
"Parameter Knob Features" section of this manual for more information.
28.
TIME – Toggles the display to show elapsed time, time remaining on the current song, or time remaining of an entire
audio CD.
29.
RECALL / STORE – Pressing and holding the RECALL button for 2 seconds will allow cue points to be stored. More
than one cue set can be stored per CD. Cue sets will be numbered sequentially per CD.
When a CD with stored cue points is inserted, the display will indicate that there are "Cue Points Available". To recall
your stored cue points press and release the RECALL button. If more than one set of cue points has been saved on a
CD, the PARAMETER knob will allow you to cycle through your stored cue sets.
30.
(PLAY) MODE – There are four playback modes:
Single: Plays the selected song, then pauses and cues the next track.
SingleReplay: Repeats the current song until manually stopped.
Random: Plays all songs on the CD in a random order.
Continuous: Plays all songs on the CD in order then repeats at the beginning.
To view file names or ID3 tag information when playing MP3s, hold RECALL/ STORE and press (PLAY) MODE.
To turn Relay Mode on or off, hold (PLAY) MODE and turn the PARAMETER knob.
31.
LCD DISPLAY – All information and functions are displayed here. CD text (if available), ID3 tag information and effects
settings are all shown here.
6

Publicité

Table des Matières
loading

Table des Matières