Publicité
Liens rapides
French on back »
Hose guide
: Drain h
: Case 1. Wash basin
' Case 2. Laundry tub
_,...,
' Case 3. Stand pipe
=
i
i
i
i
Parts ee
Tools needed
Ay
|
Drain
a
oN
retainer!
i
Hose
fe'
2
i
cs
4
i
:
8" Max
i
LIE
.
:
i
:
6" Min
nod
4
@
:
:
:
bs Mae
:
96" M
i
;
4
i
in
i
"
Max
O
Type2
Tie strap
carpenter's
/
\
;
:
;
| Tie stra
18" Min
Wrench
Bolt hole covers
Water supply hoses —_ Hose guide
(option)
Tape measure
level
Pilers
Flat screwdrilver
\
i
j
j
;
P
§
a
a
a
1
:
t
:
4
4
i
Be
we lp on
y
a
on 200 0 i.
em
5
i To 'keep the drain hose -
'The drain hose must be
'Laundry tub must ber no
'Do not insert the 'drain hose
, spout bent, use the
'placed at a height between
' shorter than 18 in (46 cm)
'too far into the stand pipe: 6
1
PREPARATION.
: 1. Check the installation location.
© CHECK : Solidly constructed floor (Not Carpeting and soft tile surfaces)
> And move the washer to the installation location.
supplied plastic hose
23. 6 in (60cm) and 35.4 in
cand no longer than 96 in
i 8 inches, and no more.
i
'guide.
:(90cm).
(245 om).
at
* Whe n n installing | the wa
h
n a | pedest
id
the
next ste
$e
st
oo
i
We om cn om on
MOVE THE WASHER TOITS FINAL LOCATION AND MAKE SURE IT IS LEVELED.
: )
REMOVING ALL SHIPPING BOLTS
Remove all shipping bolts
' Hold the shipping bolt
'Fill the holes with the
i
i
'
:
:
'with
your hand and
pull it
i
.
:
"sens
poe
meee
were
nee
wees
atthe back of washer with
"through the wide s ot on of i Supplied bolt hole covers
' Confirm whether washer i is 5 well seated and does not
: Your washer must be leveled ¢ on n all four sides. Use a a!
?
?
.
'the hole. Repeat for each
'shake. Adjust leveling legs, if necessary.
| "ensure
i sve. on all four corners of your washer to
' shipping bolt.
te
see eg
NG
anenucecnnceeeececceceaceneeceeee!
LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS.
* If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 6,7)
Visits by a Service Engineer to explain functions, maintenance or installation is
not covered by warranty.
(
:
:
:
i
3
COLD & HOT WATER HOSES INSTALLATION ON FAUCETS.
;
|
Het,
Geld
Hor cop
:
O)
:
:
:
i
i
:
:
i
LE
|
a
wet
i
i
Rubber washer "|
i
;
i
i
ut
j
'
'Level the washer by turning the leveling
Check whether washer shakes
'When your washer is leveled,
4
=
i
i
i
i
'wheel
in or out as required by using the —_' and level again, if necessary.
'tighten the locking nuts using the
|
i
Coupling
'washer
|
L
: supplied wrench.
'wrench or (-) flathead screwdriver. |
Make sure a Rubber
'Tighten Coupling by hand "Then tighten two-thirds of a Run water ina bowl or
* CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration.
'washer i is inside each
cuntil it is snug.
'turn with pliers.
'basin to get rid of any debris ;
: coupling on both ends.
:
'inside hose. Check for HOT :
'
i
i
.
.
.
2
ct
Po
12 and Cold water supply.
8
Final Test : Water leakage , Vibration & Noise
i
1. Powering your washing machine.
WATER
HOSES
INSTALLATION
ON WASHER.
2. Run a test cycle(Rinse+Spin) w with small _ amount of la laundry such as ans Towels.
.
:
:
:
:
:
(1) Check for any leakage at the hose connections.
:
1
:
.
:
:
i
* If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 3,4,5)
:
i
»
'
COLD (Left
HOT(Righ)
i
:
:
i
a x e
,
i
cf
|
Oe
Wa
(2) Check for vibration and noise.
'
mb
a
:
a
g
'Connect ¢ one e end of the
' COLD/HOT water supply
'hoses to the each COLD/
i ' HOT water supply intakes
at the back of the washer.
"Then tighten two- 'thirds ofa ai For proper operation, make
turn with pliers.
'sure both Hot & Cold hoses
'from faucets are connected to
ithe corresponding Hot / Cold
'water inlets on the washer.
Tighten Coupling by hand
until it is snug.
[] Water hose connected properly
(J Washer leveled
CI] Washer plugged in, power OK
CI Drain hose connected properly
CI Shipping bolts removed
* CAUTION: Make sure that the HOT & COLD hoses are switched with each other.
DC68-02580C-04
Installation Guide-02580C-03_EnCfrMes.indd
1
©
2012-07-20 [Hl a2ese
Publicité
