Lifetime 60336 Instructions D'assemblage

page de 132

/ 132
Signets

Liens rapides

Télécharger ce manuel

OUTSIDE

SHED

MODEL 60336

ITM./ART. 1902228

BEFORE ASSEMBLY:

• Assemble on a level platform

• At least 3 people recommended for setup

• Inspect all parts and hardware. Ensure all are

included using the Parts Identifier in the middle

of these instructions. The Parts Identifier , in

yellow, can be removed from the instructions for

quick reference

FOR OUTDOOR DOMESTIC USE ONLY! IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

TOOLS REQUIRED (NOT INCLUDED—UNLESS OTHERWISE INDICATED*)

QUESTIONS?

Call: 1-800-225-3865

(English, French, Spanish)

CONTACT LIFETIME

Live Chat: www.lifetime.com/customerservice

(click on "LIVE CHAT" tab)

For customer service in the United Kingdom and mainland europe:

Email: csinternational@lifetime.com

ASSEMBLY INSTRUCTIONS

Pour le français, voir la page 2. Para el español, ver la página 3.

5/16" (≈8 mm) Drill Bit

5/16" (≈8 mm) Masonry Drill Bit

5/32" (≈4 mm) Drill Bit (*)

CUSTOMER SERVICE:

TABLE OF CONTENTS

Icon Legend..................................................4

Warnings & Notices......................................5

Platform Construction...................................6

Truss & Beam Assembly.............................11

Transom & Gable Assembly........................17

Door Assembly.............................................26

Floor Assembly............................................40

Wall Assembly.............................................44

Shelving Installation...................................53

Door, Transom & Gable Installation............61

Parts Identiﬁ er...........................................i–iv

Roof Assembly............................................76

Wall Hook Installation................................112

Door Alignment.........................................114

Shed Anchoring.........................................116

Cleaning & Care.......................................122

Registration............................................123

Warranty.................................................124

MODEL# AND PRODUCT ID

(both are needed when contacting us)

Model Number: 60336

Product ID:

Sommaire des Matières pour Lifetime 60336

Page 1 CUSTOMER SERVICE: MODEL# AND PRODUCT ID Live Chat: www.lifetime.com/customerservice (both are needed when contacting us) Call: 1-800-225-3865 Model Number: 60336 (click on “LIVE CHAT” tab) (English, French, Spanish) For customer service in the United Kingdom and mainland europe: Product ID:...
Page 2 5/32 po (≈4 mm) Foret (*) Enregistrement.........123 Garantie............125 ® QUESTIONS ? CONTACTER LES SERVICES À LA CLIENTÈLE LIFETIME N° DE MODÈLE ET RÉFÉRENCE DU PRODUIT Composer le 1-800-225-3865 Chat en direct: www.lifetime.com/customerservice (il faut avoir les deux lors de nous contacter) (anglais, français, espagnol)
Page 3 Limpieza y cuidado..........122 Registro..............123 Garantía...............126 ® ¿PREGUNTAS? PONERSE EN CONTACTO CON LOS SERVICIOS DE CLIENTES LIFETIME Chat en vivo: www.lifetime.com/customerservice Marcar : 1-800-225-3865 MODEL E ID DEL PRODUCTO (cliquear en la lengüeta «LIVE CHAT») (se necesitan los dos al contactarnos) (inglés, francés, español)
Page 4 ICON LEGEND / LÉGENDE DES ICÔNES / SIGNIFICADO DE LOS ÍCONOS • Indicates special heed should be taken when reading. • Indique qu’une attention spéciale doit être portée à la lecture. • Indica que uno debe prestar atención al leer. •...
Page 5 WARNINGS & NOTICES / AVERTISSEMENTS ET AVIS / ADVERTENCIAS Y AVISOS English: • Failure to follow these warnings may result in serious injury or property damage and will void warranty. • To ensure safety, do not attempt to assemble this product without following the instructions carefully. •...
Page 6 PLATFORM CONSTRUCTION (MATERIALS NOT INCLUDED) / CONSTRUCTION DE LA PLATE-FORME (LES PIÈCES NE SONT PAS INCLUSES) / CONSTRUCCIÓN DE LA PLATAFORMA (LOS MATERIALES NO SON INCLUIDOS) • You must provide a platform on which to assemble your shed. Proper building permit documentation may be required in your neighborhood.
Page 7 SECTION 1 (CONTINUED) / SECTION 1 (SUITE) SECCIÓN 1 (CONTINUACIÓN) CONCRETE REQUIRED / BÉTON REQUIS CONCRETO REQUERIDO 1 yd (≈0,77 m CONCRETE PLATFORM / PLATE-FORME EN BÉTON PLATAFORMA DE CONCRETO • The concrete should be approximately 4" (≈10 cm) thick. The actual dimensions of the shed, at its widest and longest points, are 100"...
Page 8 SECTION 1 (CONTINUED) / SECTION 1 (SUITE) SECCIÓN 1 (CONTINUACIÓN) WOOD REQUIRED / BOIS REQUIS MADERA REQUERIDA RIDA WOOD PLATFORM / PLATE-FORME EN BOIS PLATA PLATAFORMA DE MADERA • All lumber must be rated for outdoor use! The actual dimensions of the shed, at its widest and longest points, are 100" x 100" (254 x 254 cm).
Page 9 SECTION 1 (CONTINUED) / SECTION 1 (SUITE) SECCIÓN 1 (CONTINUACIÓN) TOOLS, PARTS, AND HARDWARE REQUIRED / OUTILS, PIÈCES, ET QUINCAILLERIE REQUIS INSTRUMENTAL, PIEZAS, Y HERRAJE REQUERIDOS 2 in/po x 4 in/po x 88 1/4 in/po (≈5 cm x 10 cm x 224,2 cm) (x7) 2 in/po x 4 in/po x 91 1/4 in/po (≈5 cm x 10 cm x 231,8 cm) (x2) 16d 3 in/po (16d x ≈7,62 cm) (x28) 1.2.1...
Page 10 SECTION 1 (CONTINUED) / SECTION 1 (SUITE) SECCIÓN 1 (CONTINUACIÓN) TOOLS, PARTS, AND HARDWARE REQUIRED / OUTILS, PIÈCES, ET QUINCAILLERIE REQUIS INSTRUMENTAL, PIEZAS, Y HERRAJE REQUERIDOS 43 1/4 in/po x 91 1/4 in/po x 3/4 in/po 48 in/po x 91 1/4 in/po x 3/4 in/po (≈109,9 x 231,8 x 1,9 cm) (x1) (≈121,9 x 231,8 x 1,9 cm) (x1) 8d 1 1/2 in/po (8d ≈3,81 cm) (x48)
Page 11 TRUSS & BEAM ASSEMBLY / ASSEMBLAGE DE LA POUTRE ET LES FERMES / ENSAMBLAJE DE LA VIGA Y LAS CERCHAS HARDWARE REQUIRED / HERRAJE REQUERIDO / QUINCAILLERIE REQUISE Hardware Bag / Bolsa de herraje Sac de quincaillerie GJZ (x8) DAH (x20) GKS (x8) GQO (x8) BLB (x12)
Page 12 SECTION 2 (CONTINUED) / SECCIÓN 2 (CONTINUACIÓN) SECTION 2 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS ADC (x1) GJZ (x6) GQO (x6) • Attach the six (6) “L” brackets (GQO) to the beam (GKT) using six (6) screws (GJZ). Do not overtighten. •...
Page 13 SECTION 2 (CONTINUED) / SECCIÓN 2 (CONTINUACIÓN) SECTION 2 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS 7/16" (≈11 mm) DAH (x8) GKS (x8) • Attach a vertical truss support (GKC) to each end of the beam with two (2) gussets (GKG). Do not overtighten. •...
Page 14 SECTION 2 (CONTINUED) / SECCIÓN 2 (CONTINUACIÓN) SECTION 2 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS GJZ (x2) GQO (x2) • Attach an “L” bracket (GQO) to the end of each vertical support using one (1) screw (GJZ) each. Do not overtighten. Set the assembly aside. •...
Page 15 SECTION 2 (CONTINUED) / SECCIÓN 2 (CONTINUACIÓN) SECTION 2 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS BLB (x4) • Slide a short gutter channel (GKV) into a long truss gutter channel (GKW) and align the four square holes. •...
Page 16 SECTION 2 (CONTINUED) / SECCIÓN 2 (CONTINUACIÓN) SECTION 2 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS 7/16" (≈11 mm) BLB (x8) DAH (x12) • Secure each bolt with a nut (DAH). Do not overtighten. •...
Page 17 TRANSOM & GABLE ASSEMBLY / ASSEMBLAGE DE L’IMPOSTE ET DES PIGNONS / ENSAMBLAJE DEL MONTANTE Y DE LAS FACHADAS HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware Bag / Sac de quincaillerie Bolsa de herraje ADK (x8) GKP (x8) ADZ (x72) AEE (x8) GJZ (x2)
Page 18 TRANSOM & GABLE ASSEMBLY / ASSEMBLAGE DE L’IMPOSTE ET DES PIGNONS / ENSAMBLAJE DEL MONTANTE Y DE LAS FACHADAS PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS Plastic Parts / Pièces en plastique Piezas de plástico GDT (x1) GDU (x1) GDV (x1) TOOLS REQUIRED (NOT INCLUDED) / OUTILS REQUIS (NON INCLUS) / INSTRUMENTAL REQUERIDO (NO INCLUIDO)
Page 19 SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADK (x8) GKP (x8) Only hand-tighten these nuts Serrer ces écrous à la main seulement Apretar estas tuercas sólo a mano TRANSOM FRAME ASSEMBLY / ASSEMBLAGE DU CADRE DE L’IMPOSTE ENSAMBLAJE DEL ARMAZÓN DEL TRAVESAÑO...
Page 20 SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x2) GLF (x1) • Secure the upper deadbolt bracket (GLF) to the transom using two (2) screws (GJZ). Tighten securely. Please note the orientation of the bracket and the positions of the supports.
Page 21 SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS EPI (x1) TRANSOM ASSEMBLY / ASSEMBLAGE DE L’IMPOSTE ENSAMBLAJE DEL TRAVESAÑO • There is a narrow groove (illustrated in black) running along the outside of the window on the transom (GDT). Starting at the top, left corner of the groove in the left window, lay an 1/8"...
Page 22 SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x14) • Peel the protective ﬁ lm from both sides of the transom window pane (GKH). Secure the window pane to the transom (GDT) using fourteen (14) screws (ADZ) each.
Page 23 SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS EPI (x1) EPH (x1.5) GABLE ASSEMBLY / ASSEMBLAGE DES PIGNONS ENSAMBLAJE DE LAS FACHADAS • There is a narrow groove (illustrated in black) running around the windows on the back of the gable. Starting with the square window, at the top, left corner of the groove in the left gable, lay an 1/8"...
Page 24 SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x29) • Peel the protective ﬁ lm from both sides of the gable window pane (HIY). Secure one (1) window pane (HIY) to the left gable (GDU) using fourteen (14) screws (ADZ).
Page 25 SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS AEE (x8) ADX (x8) GKF (x2) GIE (x1) GIF (x1) ADZ (x29) EPI (x1) EPH (x1.5) • Secure a vent (GIF) and screen (GKF) to the left gable (GDU) using four (4) screws (ADX) and washers (AEE). •...
Page 26 LEFT DOOR ASSEMBLY / ASSEMBLAGE DE LA PORTE GAUCHE / ENSAMBLAJE DE LA PUERTA IZQUIERDA HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware Bags / Sacs de quincaillerie Bolsas de herraje AEE (x3) AEB (x2) DGR (x1) DGS (x1) Lower / Inférieur Inferior...
Page 27 SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS BBH (x1) • Slide a square tube (GJT) into the square hole at the bottom of the Left Door (BDJ) until about 6"...
Page 28 SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ACH (x2) AEB (x2) AAB (x2) EOY (x1) • Attach the door latch bracket (EOY) to the door using the hardware indicated. Only hand-tighten for now. •...
Page 29 SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • Turn the door onto its front. There are seven small impressions (divots) running along the edge of the door—two at each end and three inbetween.
Page 30 SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x3) • Set the inner door channel (GJQ) onto the door as shown. Align the three holes in the channel with the three holes in the door.
Page 31 SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x4) DGS (x1) Upper / Supérieur Superior DGR (x1) Lower / Inférieur Inferior • Secure the upper and lower latches (DGS and DGR) to the door using two (2) screws (GJZ) each. The latches should move freely.
Page 32 SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS BYZ (x3) AEE (x3) • Attach the front and rear handle pieces (GJR and GJS) together. Secure the handle to the door using the hardware indicated. •...
Page 33 SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • Slide a hinge tube (GLY) into the hole at the bottom of the door. If necessary, use a rubber mallet to gently tap the tube into place.
Page 34 RIGHT DOOR ASSEMBLY / ASSEMBLAGE DE LA PORTE DROITE / ENSAMBLAJE DE LA PUERTA DERECHA HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware Bag / Sac de quincaillerie / Bolsa de herraje GJZ (x1) ACH (x2) FJP (x1) EPA (x1) FUA (x2) AAB (x2) ADK (x2)
Page 35 SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS BBH (x1) • Slide a square tube (GJT) into the square hole at the bottom of the right door (BDK) until about 6" (≈15 cm) of the tube hang out of the hole.
Page 36 SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS ACH (x2) FJP (x1) AAB (x2) FUA (x2) EPA (x1) EOZ (x1) ADK (x2) • Attach the locking hardware using the hardware included. Only hand-tighten the nuts for now. •...
Page 37 SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x1) ADC (x1)* • Using the 5/32" (≈4 mm) drill bit (GHO) included and an electric drill, drill through the divot near the bottom edge of the door and into the square tube.
Page 38 SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS BYZ (x3) AEE (x3) GJR (x1) GJS (x1) • Attach the front and rear handle pieces (GJR and GJS) together. Secure the handle to the door using the hardware indicated. •...
Page 39 SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS • Slide a hinge tube (GLY) into the hole at the bottom of the door. If necessary, use a rubber mallet to gently tap the tube into place.
Page 40 FLOOR ASSEMBLY / ASSEMBLAGE DU PLANCHER / ENSAMBLAJE DEL PISO HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware Bag / Sac de quincaillerie Bolsa de herraje GJZ (x2) GLG (x1) GLU (x2) CWU (x20) Note: These are not anchoring screws. Their sole purpose is to fasten together the ﬂ oor panels. Remarque : Ces vis ne sont pas les vis d’ancrage.
Page 41 SECTION 6 (CONTINUED) / SECTION 6 (SUITE) SECCIÓN 6 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • Hold an inner ﬂ oor panel (AFX) at an angle and slide the tabs along the edge underneath an outer ﬂ oor panel (AGR). The tabs interlock.
Page 42 SECTION 6 (CONTINUED) / SECTION 6 (SUITE) SECCIÓN 6 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • There are four places for weep holes in the ﬂ oor: one at each end of the inner ﬂ oor panel and one on each outer ﬂ oor panel. These help with drainage.
Page 43 SECTION 6 (CONTINUED) / SECTION 6 (SUITE) SECCIÓN 6 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS CWU (x12) GLG (x1) GJZ (x2) Note: These are not anchoring screws. Their sole purpose is to fasten together the ﬂ oor panels. Remarque : Ces vis ne sont pas les vis d’ancrage.
Page 44 WALL ASSEMBLY / ENSAMBLE DE LOS MUROS / ASSEMBLAGE DES MURS HARDWARE REQUIRED / HERRAJE REQUERIDO / QUINCAILLERIE REQUISE Hardware Bag / Bolsa de herraje Sac de quincaillerie GJZ (x6) ADZ (x45) AHS (x6) PARTS REQUIRED / PIEZAS REQUERIDAS / PIÈCES REQUISES Metal Parts / Pièces en métal Piezas de metal...
Page 45 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS ADZ (x16) • At the bottom of the back of each wall panel is a three-letter ID (AHD, AGN, AGW or AGY). This will help you identify the correct panel during assembly.
Page 46 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS • Insert a square tube into the hole at the bottom of each wall panel (AHD), six in all, until the end cap is ﬂ ush with the bottom of the panel.
Page 47 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS ADC (x1) GJZ (x6) GHO (x1) • Using an electric drill and the 5/32" (≈4 mm) drill bit (GHO) provided, drill a hole through the divot and into the square tube at the location indicated.
Page 48 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS • Insert a wall tube (GLZ) into the hole at the bottom of the front, right corner wall panel (AGY). If necessary, use a rubber mallet to gently tap the tube into place.
Page 49 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS • Insert the two left-most tabs at the bottom of the corner panel (AGY) into the two right-most slots along the front, right edge of the ﬂ...
Page 50 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS ADZ (x25) 7.10 • Secure the panels together using • Insert the tabs of two wall panels (AHD) and slide the panels toward the front corner.
Page 51 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS ADZ (x15) 7.13 7.14 • Insert this Corner Panel (AGW) like the ﬁ rst Corner • Attach two Wall Panels (AHD) to the left side of the Wall Panel.
Page 52 SECTION 7 (CONTINUED) / SECCIÓN 7 (CONTINUACIÓN) SECTION 7 (SUITE) TOOLS AND HARDWARE REQUIRED / INSTRUMENTAL Y HERRAJE REQUERIDOS OUTILS ET QUINCAILLERIE REQUIS ADZ (x5) 7.16 • Insert the last corner panel (AGN) in the same way as the previous one. Secure with screws (ADZ). •...
Page 53 SHELVING INSTALLATION / INSTALLATION DU RAYONNAGE / INSTALACIÓN DE LA ESTANTERÍA HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware Bag / Sac de quincaillerie Bolsa de herraje GJZ (x8) ADZ (x8) FEX (x4) GJY (x2) GJW (x2) PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS Metal Parts / Pièces en métal Piezas de metal...
Page 54 SECTION 8 (CONTINUED) / SECTION 8 (SUITE) SECCIÓN 8 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • There are three pairs of indentations (divots) available for the height of the long shelf. These are located on the two rear wall panels.
Page 55 SECTION 8 (CONTINUED) / SECTION 8 (SUITE) SECCIÓN 8 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x4) • There are three pairs of holes available for shelf heights for the long shelf. These are located on the rear corner wall panels.
Page 56 SECTION 8 (CONTINUED) / SECTION 8 (SUITE) SECCIÓN 8 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x4) GJW (x2) • Secure the end shelf brackets (GJW) to the anchors attached in the previous step with two (2) screws (GJZ) each. The brackets must be at the same height.
Page 57 SECTION 8 (CONTINUED) / SECTION 8 (SUITE) SECCIÓN 8 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x4) GJY (x2) • Secure two (2) shelf brackets (GJY) to the walls by inserting two (2) screws (GJZ) through each bracket and into the square tubes in the wall panels.
Page 58 SECTION 8 (CONTINUED) / SECTION 8 (SUITE) SECCIÓN 8 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS •Snap the support tube (GJX) into the grooves along the bottom of the long shelf (AFV). They snap into place. To orient the shelf correctly, the three-letter ID, AFV, on the bottom of the shelf should be on the left-hand side.
Page 59 SECTION 8 (CONTINUED) / SECTION 8 (SUITE) SECCIÓN 8 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • Lower the long shelf onto the shelf brackets. The word “BACK” should be on top and next to the rear wall. •...
Page 60 SECTION 8 (CONTINUED) / SECTION 8 (SUITE) SECCIÓN 8 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x8) • Secure the shelf to the shelf brackets using eight (8) screws (ADX). Do not overtighten the screws. •...
Page 61 DOOR, TRANSOM AND GABLE INSTALLATION / INSTALLATION DES PORTES, DE L’IMPOSTE, ET DES PIGNONS / INSTALACIÓN DE LAS PUERTAS, DEL MONTANTE, Y DE LAS FACHADAS HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware Bag / Sac de quincaillerie Bolsa de herraje ADZ (x42) GLW (x4) GLE (x4)
Page 62 DOOR, TRANSOM AND GABLE INSTALLATION / INSTALLATION DES PORTES, DE L’IMPOSTE, ET DES PIGNONS / INSTALACIÓN DE LAS PUERTAS, DEL MONTANTE, Y DE LAS FACHADAS PARTS REQUIRED / PIEZAS REQUERIDAS / PIÈCES REQUISES Plastic Parts / Piezas de plástico Pièces en plastique (x1) (x1) (x1)
Page 63 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x2) GLW (x4) • Set the beam assembly from steps 2.1–2.3 into place. Align the holes in the wall panels with those in the vertical supports and secure with two (2) screws (GLW) each.
Page 64 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 7/16 (≈11 mm) ACH (x2) AZP (x2) • Secure the beam assembly to the side walls using a bolt (ACH) and nut (AZP) for each side. Do not overtighten. •...
Page 65 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS CONTENTS OF BOX 1 / CONTENU DE LA BOITE 1 CONTENIDO DE LA CAJA 1 GDT (x1) GDU (x1) GDV (x1) AFX (x1) AGR (x2) GDW (x1) AFV (x1) AGQ (x4) CONTENTS METAL KIT 1 / CONTENU DE LA TROUSSE DE PIÈCES EN MÉTAL 1 CONTENIDO DEL KIT DE PIEZAS DE METAL 1...
Page 66 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS CONTENTS METAL KIT 1 / CONTENU DE LA TROUSSE DE PIÈCES EN MÉTAL 1 CONTENIDO DEL KIT DE PIEZAS DE METAL 1 GKC (x2) GKT (x1) CONTENTS METAL KIT 2 / CONTENU DE LA TROUSSE DE PIÈCES EN MÉTAL 2 CONTENIDO DEL KIT DE PIEZAS DE METAL 2 GAT (x6)
Page 67 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS CONTENTS OF BOX 2 / CONTENU DE LA BOITE 2 CONTENIDO DE LA CAJA 2 GKD (x2) AGN (x1) AGY (x1) AGW (x2) AHD (x6) BDJ (x1) BDK (x1) CONTENTS OF SMALL PARTS KIT / CONTENU DE LA TROUSSE DE PETITES PIÈCES CONTENIDO DEL KIT DE PIEZAS PEQUEÑAS GKX (x16)
Page 68 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS HARDWARE BAGS / SACS DE QUINCAILLERIE BOLSAS DE HERRAJE...
Page 69 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ACB (x2) • Hold the corner wall panel together at a 90°, and insert a screw (ACB) through right edge and into the front edge as shown. Do not overtighten.
Page 70 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x12) • Place the right gable assembly from steps 3.5–3.6 against the right wall and align the holes. The rear end of the gable slides down over the rear wall extension.
Page 71 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x12) • Repeat the last step for the left side of the shed. The rear end of the gable slides down over the rear wall extension. Do not over- tighten.
Page 72 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • Set the rear wall extension (GDW) on the rear wall panels. Slide the tabs at the ends into the slots on the Gables. •...
Page 73 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x12) • Secure the extension to the rear wall with twelve (12) screws (ADZ). Do not overtighten. •...
Page 74 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GLE (x1) • Pull the hinge tube in the wall up about 2" (≈5 cm) and slide a hinge cap (GLE) underneath it. Pull the hinge tube back down and insert it through the hinge cap and into the bushing from step 6.4.
Page 75 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GLE (x1) • Pull the hinge tube down out of the Door a few inches and insert it in the hinge cap (GLE) in the orientation indicated. The notch in the hinge tube ﬁ...
Page 76 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GLE (x2) 9.10 • Repeat steps 9.8–9.9 for the right door. • Répéter les étapes 9.8 – 9.9 pour la porte droite. •...
Page 77 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 9.11 • (1) Place the grooves in the transom assembly from step 3.4 against the two tabs on the gables and (2) slide the transom downward over the corner panels.
Page 78 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GHO 5/32 in/po ADZ (x4) 4 mm 9.12 • Secure the transom to the corner wall panels with four (4) screws (ADZ) at the locations indicated. Use the 5/32" (5 mm) drill bit to drill through the transom divots and into the hinge tubes.
Page 79 SECTION 9 (CONTINUED) / SECTION 9 (SUITE) SECCIÓN 9 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x2) GNC (x2) 9.13 • Secure a rain stop (GNC) to the bottom of the front corner wall panels using one (1) screw (ADZ) each. •...
Page 80 ROOF ASSEMBLY / MONTAGE DU TOIT / ENSAMBLAJE DEL TECHO HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware Bag / Sac de quincaillerie Bolsa de herraje ADV (x30) GJZ (x94) FEX (x110) GLB (x3) BLB (x6) AZP (x6) AHS (x2) ACB (x4) ADZ (x2) PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS...
Page 81 ROOF ASSEMBLY / MONTAGE DU TOIT / ENSAMBLAJE DEL TECHO PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS Plastic Parts / Pièces en plastique Piezas de plástico CVC (x4) AGQ (x4) TOOLS REQUIRED (NOT INCLUDED) / OUTILS REQUIS (NON INCLUS) / INSTRUMENTAL REQUERIDO (NO INCLUIDO) 7/16 in/po (≈11 mm) 3/8 in/po (≈10 mm)
Page 82 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 7/16 in/po (≈11 mm) BLB (x6) AZP (x6) 10.1 • Set the three trusses from steps 2.4–2.7 onto the transom and rear wall extension and between the brackets on the beam as shown.
Page 83 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.2 • Snap four (4) roof supports (GKX) into the grooves on the back of a lower roof panel (AGQ). Repeat this step for the rest of the lower roof panels.
Page 84 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x17) 10.3 • Snap seventeen (17) anchors (FEX) in the direction shown into only the slots indicated in this lower roof panel. DO NOT REPEAT this step for the other three (3) lower roof panels.
Page 85 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x2) 10.4 • Using the lower roof panel from step 10.3, secure a diagonal roof support (GKQ) to the location indicated using two (2) screws (GJZ).
Page 86 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x17) 10.5 • Take the second lower roof panel and snap seventeen (17) anchors (FEX) in the direction shown into only the slots indicated in this lower roof panel.
Page 87 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x2) 10.6 • Take the lower roof panel from step 10.5 and secure a diagonal roof support (GKQ) at the location indicated using two (2) screws (GJZ).
Page 88 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x28) 10.7 • Snap fourteen (14) anchors (FEX) in the direction shown into only the slots indicated in this lower roof panel. Repeat this step for the last lower roof panel.
Page 89 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x9) 10.8 • Snap nine (9) anchors (FEX) in the direction shown into only the slots indicated in this upper roof panel (CVC). •...
Page 90 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x2) 10.9 • Take the upper roof panel from step 10.8 and secure a diagonal roof support (GKQ) to the panel at the location indicated using two (2) screws (GJZ).
Page 91 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x9) 10.10 • Snap nine (9) anchors (FEX) in the direction shown into only the slots indicated in this upper roof panel. •...
Page 92 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x2) 10.11 • Take the upper roof panel from step 10.10 and secure a diagonal roof support (GKQ) to the panel at the location indicated using two (2) screws (GJZ).
Page 93 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x14) 10.12 • Snap seven (7) anchors (FEX) in the direction shown into only the slots indicated in this upper roof panel. These last two upper roof panels will go in the middle of the top of the roof.
Page 94 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.13 • Take the lower roof panel from steps 10.3–10.4 and set it down on the left side of the shed. The diagonal brace should be at the bottom left.
Page 95 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x14) 10.14 • Align the holes in the gable, rear wall and truss with the anchors in the roof panel. Secure the panel to the gable, rear wall and truss with fourteen (14) screws (GJZ) into the anchors only at the locations shown.
Page 96 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.15 • Take the upper roof panel from steps 10.8–10.9 and set it onto the upper left side of the roof as shown. Note the position of the diagonal brace;...
Page 97 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x7) 10.16 • Secure the upper roof panel to the gable, transom, lower roof panel and truss by inserting seven (7) screws (GJZ) through the gable, transom, lower roof panel and truss and into the anchors at the locations shown.
Page 98 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.17 • Take the two lower roof panels from step 10.7 and set the edges into the trusses as shown. Note that these two panels have no diagonal brace.
Page 99 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x24) 10.18 • Secure the lower roof panels to the rear wall and trusses using twenty-four (24) screws (GJZ) only at the locations indicated.
Page 100 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.19 • Take the two upper roof panels from step 10.12 and set them onto the upper center positions of the roof as shown. Note that these two panels have no diagonal brace.
Page 101 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x14) 10.20 • Secure the upper roof panels to the transom, trusses and lower roof panels using fourteen (14) screws (GJZ) only at the locations indicated.
Page 102 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.21 • Take the lower roof panel from step 10.5–10.6 and set it onto the lower right side of the roof as shown. Note the position of the diagonal brace;...
Page 103 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x14) 10.22 • Align the holes in the gable, rear wall and truss with the anchors in the roof panel. Secure the panel to the gable, rear wall and truss with fourteen (14) screws (GJZ) into the anchors only at the locations shown.
Page 104 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.23 • Take the upper roof panel from steps 10.10–10.11 and set it onto the upper right side of the roof as shown. Note the position of the diagonal brace;...
Page 105 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x7) 10.24 • Like step 10.16, secure the upper roof panel to the gable, transom, lower roof panel and truss by inserting seven (7) screws (GJZ) through the gable, transom, lower roof panel and truss and into the anchors at the locations shown.
Page 106 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GLB (x3) 10.25 • Insert a bee guard (GLB) up into a truss and align the holes in the bee guard with those in the truss and roof panels. Repeat this step for the other trusses at the rear of the shed.
Page 107 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS GJZ (x6) 10.26 • At the rear of the shed, secure the bee guards to the trusses and roof with two (2) screws (GJZ) per guard at the locations indicated.
Page 108 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS FEX (x2) 10.27 • Insert an anchor (FEX) into the transom at the two locations shown. • Insérer un ancre (FEX) dans l’imposte aux deux endroites indiqués. •...
Page 109 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.28 • Set the metal transom frame, from steps 3.1–3.3, up against the transom and align the holes in the frame with those in the transom.
Page 110 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 10.29 • The curved ends of the brackets should ﬁ t just inside the grooves in the gable. The cap nuts must be loose. •...
Page 111 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ACB (x2) 10.31 • Insert a screw (ACB) through the bottom hole in the transom and into the wall hinge tube. Repeat this step for the other wall hinge tube.
Page 112 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ACB (x2) ADV (x20) 10.32 • While another adult gently pushes against the outside of the transom, secure the metal transom frame to the transom using twenty (20) screws (ADV) and two (2) screws (ACB) at the locations indicated.
Page 113 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADZ (x2) 10.33 • Secure the transom-to-gable bracket to the left gable using one (1) screw (ADZ). Repeat this step for the right gable. •...
Page 114 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 3/8 in/po (≈10 mm) AHS (x2) 10.34 • Secure the cap nuts from step 3.2. • Bien serrer les écrous borgnes de l’étape 3.2. •...
Page 115 SECTION 10 (CONTINUED) / SECTION 10 (SUITE) SECCIÓN 10 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADV (x10) 10.36 • Secure a square tube to the top of the gable (next to the roof panel) using ﬁ ve (5) screws (ADV). The square tube rests on top of the metal transom frame and the beam.
Page 116 WALL HOOK INSTALLATION / INSTALLATION DES CROCHETS MURAUX / INSTALACIÓN DE LOS GANCHOS MURALES ACCESSORIES REQUIRED / ACCESSOIRES REQUIS / ACCESORIOS REQUERIDOS Wall Hooks Bag / Sac de crochets muraux Bolsa de ganchos murales GKU (x6) PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS NO PARTS REQUIRED FOR THIS SECTION AUCUNE PIÈCE REQUISE POUR CETTE SECTION NINGUNA PIEZA REQUERIDA PARA ESTA SECCIÓN...
Page 117 SECTION 11 (CONTINUED) / SECTION 11 (SUITE) SECCIÓN 11 (CONTINUACIÓN) TOOLS AND ACCESSORIES REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y ACCESORIOS REQUERIDOS GKU (x6) 11.1 • Insert the six (6) wall hooks (GKU) into any of the notches in the wall panels (any wall of the shed). Then push downward to lock them in place.
Page 118 DOOR ALIGNMENT / ALIGNEMENT DES PORTES / ALINEACIÓN DE LAS PUERTAS HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS Plastic Parts / Pièces en plastique Piezas de plástico AIX (x4) TOOLS REQUIRED (NOT INCLUDED) / OUTILS REQUIS (NON INCLUS) / INSTRUMENTAL REQUERIDO (NO INCLUIDO)
Page 119 SECTION 12 (CONTINUED) / SECTION 12 (SUITE) SECCIÓN 12 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS AIX (x4) 12.1 • If the Doors are not level, follow the steps below to even them out. •...
Page 120 SHED ANCHORING / ANCRAGE DE L’ABRI / ANCLAJE DE LA CASETA HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS TOOLS REQUIRED (NOT INCLUDED) / OUTILS REQUIS (NON INCLUS) / INSTRUMENTAL REQUERIDO (NO INCLUIDO) 5/16"...
Page 121 SECTION 13 (CONTINUED) / SECTION 13 (SUITE) SECCIÓN 13 (CONTINUACIÓN) FOR A CONCRETE PLATFORM / POUR UNE PLATE-FORME EN BÉTON PARA UNA PLATAFORMA DE CONCRETO 5/16 in/po (≈8 mm) 13.1 • If you plan on anchoring your shed to a concrete platform, you must purchase the correct anchoring hardware. We recommend using a hammer drill, 5/16"...
Page 122 SECTION 13 (CONTINUED) / SECTION 13 (SUITE) SECCIÓN 13 (CONTINUACIÓN) FOR A WOOD PLATFORM / POUR UNE PLATE-FORME EN BOIS PARA UNA PLATAFORMA DE MADERA 5/16 in/po (≈8 mm) 7/16 in/po (≈11 mm) 13.1 • If you plan on anchoring your shed to a wood platform, you must purchase the correct anchoring hardware. We recommend using a drill, 5/16"...
Page 123 NOTES / REMARQUES / NOTAS...
Page 124 NOTES / REMARQUES / NOTAS...
Page 125 NOTES / REMARQUES / NOTAS...
Page 126 ® product purchase. By following the instructions below, your new Lifetime product should provide you with years of service and enjoyment. The polyethylene panels are stain and solvent resistant. Most stains can be removed using a mild soap and a soft-bristled brush.
Page 127 à des tiers, et ne leur permettra pas d’utiliser vos données personnelles à leurs propres ﬁ ns. Nous vous invitons à lire notre politique de conﬁ dentialité à www.lifetime.com (en anglais seulement) ENREGISTRER CE PRODUIT aujourd’hui! REGISTRAR EL PRODUCTO EN LÍNEA EN WWW.LIFETIME.COM...
Page 128 THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. Lifetime Lawn and Garden products are warranted to the original purchaser to be free from defects in material or imperfections that impair the use of the product. Defects resulting from misuse, abuse or negligence will void this warranty.
Page 129 Cette garantie n’est pas transférable et se limite expressément à la réparation ou au remplacement d’un produit défectueux. Si le produit est défectueux au sens de cette garantie, Lifetime Products, Inc. réparera ou remplacera les pièces défectueuses sans frais pour l’acheteur. Les frais d’expédition en partance ou en provenance de l’usine et les autres frais liés au retrait, à...
Page 130 NO ESTÁN DISPONIBLES O SON OBSOLETAS. El comprador original recibe una garantía de que los productos de césped y jardín de Lifetime están libres de defectos de material o mano de obra durante un período de 10 años a partir de la fecha de compra original al por menor.
Page 131 IMPORT INFORMATION / IMPORTATIONS / INFORMACIÓN DE IMPORTACIONES Costco Wholesale Korea, Ltd. Distributed by: 40, Iljik-ro Costco Wholesale Corporation Gwangmyeong-si P.O. Box 34535 Gyeonggi-do, 14347, Korea Seattle, WA 98124-1535 1899-9900 1-800-774-2678 www.costco.co.kr www.costco.com Importado por: Importadora Primex S.A. de C.V. Costco Wholesale Canada Ltd.* Blvd.
Page 132 Or call 1-800-424-3865 ® AMÉLIORER VOTRE ACHAT LIFETIME EN AJOUTANT DES ACCESSOIRES OU D’AUTRES PRODUITS ® Pour acheter des accessoires ou d’autres produits Lifetime , nous rendre visite à : www.lifetime.com Ou composer le 1-800-424-3865 ® MEJORAR SU COMPRA LIFETIME Y AÑADIR ACCESORIOS U OTROS PRODUCTOS EXCELENTES...

Ce manuel est également adapté pour:

1902228