ADEO SCREEN ONSUPERIOR Manuel D'installation Et D'utilisation page 12

ENGLISH – Rolling screen installation and operation manual
The type of motor installed on the product is identified by a label applied on each product showing the CE logo. When unwrapping the product please check the model type indicated on the label in order to
perform the installation and cable connections correctly. Should the power of the motor be different from that of the supply network of the installation place, please contact an electrician to have a current and
Hz transformer installed.
electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be fitted with an omnipolar selector switch with contact opening distance of at least
3 mm. For the screen's control use only the selector switch provided by manufacturer, or equivalent model, and follow the instructions of the connection diagram shown on left (if the motor is mounted on
the left, the colours of the wires must be inverted, i.e. descending = brown, ascending = black). The selector switch must be mounted within sight distance of the product, at a 1.5 - 1.8 m height from the
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's optimal and unaltered performance over time. Prior to carrying
out any operation on electrical parts ensure that power supply is disconnected. In screens fitted with cases the motor is positioned on the right-hand side of the screen as seen from the front (upon request
it can be located on the left). Never connect two or more motors to the same selector switch without a control unit or two switches to the same motor.
Somfy 230V 50Hz
Somfy 230V 50Hz
Somfy 120V 60Hz
Somfy 120V 60Hz
Somfy 100V 50-60Hz
Somfy 100V 50-60Hz
Made by Adeo Screen Sp. Z o.o. (Poland) Specifications are subject to change without notice. E&OE
Doc: ONSUPERIOR Installation Manual rev4 |10.02.2021
Please verify that you are working with the latest revision of this document before specifying your screen.
09 MOTOR TYPE IDENTIFICATION –CHARACTERISTICS – ELECTRICAL CONNECTION
floor. To connect the wires to the supplied switch, remove the plastic front plates to access the lock/unlock buttons
Viewing width <=2000 for format 1.00-1.33-1.60
Viewing width <=3000 for other formats
Viewing width >2000 for format 1.00-1.33-1.60
Viewing width >3000 for other formats
Viewing width <=2000 for format 1.00-1.33-1.60
Viewing width <=3000 for other formats
Viewing width >2000 for format 1.00-1.33-1.60
Viewing width >3000 for other formats
Viewing width <=2000 for format 1.00-1.33-1.60
Viewing width <=3000 for other formats
Viewing width >2000 for format 1.00-1.33-1.60
Viewing width >3000 for other formats
ELECTRICAL CONNECTION:
WARNING:
Technical characteristics:
Frequency: ~Hz50
Power: 100W
Torque: 10Nm
Speed: 12Rpm
Duty cycle: S2 4min
Cable length: 3m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Frequency: ~Hz50
Power: 160W
Torque: 30Nm
Speed: 12Rpm
Duty cycle: S2 4min
Cable length: 3m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Frequency: ~Hz60
Power: 96W
Torque: 88in. lbs
Speed: 14Rpm
Duty cycle: S2 4min
Cable length: 3m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Frequency: ~Hz60
Power: 190W
Torque: 220in. lbs
Speed: 20Rpm
Duty cycle: S2 4min
Cable length: 3m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Frequency: ~Hz50-60
Power: 80W
Torque: 10Nm
Speed: 12/14Rpm
Duty cycle: S2 4min
Cable length: 3m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Frequency: ~Hz50-60
Power: 160W
Torque: 20Nm
Speed: 17/20Rpm
Duty cycle: S2 4min
Cable length: 3m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Connection for each motor:

Brown (Up)

Black (Down)

Blue (Common)

Yellow Green (Ground)
Page 12