Product Features; Technical Data; Noise/Vibration Information - Bosch EasyCut 12 NanoBlade Notice Originale

Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for domestic use only. It is inten-
ded for cutting branches, slats, hardwood and softwood. It is
suitable for straight cuts.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Saw blade
(2) Base plate
(3) Lock-off button for on/off switch
(4) On/off switch
(5) Battery
(6) Battery release button
(7) Suspension strap
(8) Battery charge indicator
(9) Cover of the saw blade receptacle
(10) Locking lever of the saw blade receptacle cover
(11) Handle (insulated gripping surface)
(12) Saw blade receptacle

Technical Data

All-purpose saw
Article number
Rated voltage
Max. cutting depth
Weight according to
EPTA‑Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 62841‑2‑11.
Typically, the A-weighted sound pressure level of the power
tool is 75 dB(A). Uncertainty K = 5 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑11:
Bosch Power Tools
Cutting boards with saw blade NanoBlade Wood Speed 65:
a
h,B
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
EasyCut 12
3 603 CC9 0..
V= 12
Battery Charging (see figure B)
mm 65
u
A)
kg 0.90
Note: The battery is supplied partially charged. To ensure
°C 0 to +35
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
°C –20 to +50
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
PBA 12V...
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
GAL 12...
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
To remove the battery (5), press the release button (6) and
pull the battery back and out of the power tool. Do not use
force to do this.
Battery charge-control indicator
When the on/off switch (4) is pressed in halfway or com-
pletely, the battery charge indicator (8) indicates the bat-
tery's state of charge for a few seconds. It consists of an LED
which lights up in two colours.
2 2
< 2.5 m/s , K = 1.5 m/s .
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 672 | (17.12.2020)
English | 13