Publicité
Liens rapides
© 2009-2010, Moog Videolarm, Inc. All Rights Reserved
F D W 7 5
Fusion Dome (Outdoor Wall Mount with Housing)
Installation and Operation Instructions for the following models:
FDW75C2N
IP Network Ready 7" Outdoor dome hsg w/wall mount, clear dome, w/24Vac
input, heater/blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.
FDP75C2N
IP Network Ready 7" Outdoor dome hsg w/pendant mount, clear dome, w/24Vac
input, heater/blower, fan an IP Network PTZ camera,120 to 24Vac transformer.
IFDW75CN
IP Network Ready 7" Indoor dome hsg w/wall mount, clear dome, w/24Vac input,
heater/blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.
IFDP75CN
IP Network Ready 7" Indoor dome hsg w/pendant mount, clear dome, w/24Vac
input, heater/blower, fan an IP Network PTZ camera,120 to 24Vac transformer.
FDW75C2NE IP Network Ready 7" Outdoor dome hsg w/wall mount, clear dome, w/24Vac
input, heater/blower, fan an IP Network PTZ camera. (European Model)
FDP75C2NE IP Network Ready 7" Outdoor dome hsg w/pendant mount, clear dome, w/24Vac
input, heater/blower, fan an IP Network PTZ camera. (European Model)
Before attempting to connect or operate this product,
please read these instructions completely.
All manuals and user guides at all-guides.com
www.videolarm.com
CERTIFIED
81-IN5358
07-26-2010
Publicité
Manuels Connexes pour Moog Videolarm FDW75
Sommaire des Matières pour Moog Videolarm FDW75
- Page 1 All manuals and user guides at all-guides.com © 2009-2010, Moog Videolarm, Inc. All Rights Reserved F D W 7 5 Fusion Dome (Outdoor Wall Mount with Housing) www.videolarm.com Installation and Operation Instructions for the following models: FDW75C2N IP Network Ready 7” Outdoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.
- Page 2 All manuals and user guides at all-guides.com IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth.
- Page 3 All manuals and user guides at all-guides.com LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows: PRODUCTCATEGORY PARTS LABOR All Enclosuresand Electronics Five (5) Years Five (5) Years Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan...
- Page 4 All manuals and user guides at all-guides.com Electrical Specifications Contents of Box Power 24VAC FDW75 Class 2 Only 24 VAC 26 Watts Accessories: Heater: 25 Watts, Blower: 1 Watt Camera Power: 40 Watts Max Tools Required: .100” Flat Head Screwdriver Phillips Head Screwdriver...
- Page 5 All manuals and user guides at all-guides.com WALL MOUNTING 4”-5” Trim incoming control & power wires to 4”- 5”, Bracket is designed for 45° conduit tting (If using the for either wall or pendent bracket conduit). Run wire into bracket secure to wall. •...
- Page 6 All manuals and user guides at all-guides.com WALL MOUNTING Important Gasket Must be in place 26 Watts COAX (coax wire not supplied) Wiring the dome can be completed by Align large arrows referring to the diagram. • Atar con alambre la bóveda puede ser terminada •...
- Page 7 All manuals and user guides at all-guides.com FOR PENDENT/ WALL MOUNTING 4”-5” Trim incoming control and power wires to 4-5 for Secure lanyard to lanyard clip either wall or pendent bracket • La tapa segura de la cubierta SM5 con mercancías duras •...
- Page 8 All manuals and user guides at all-guides.com Important Gasket Must be in place Align large arrows To lock turn clockwise • Alinee las flechas grandes • Alinee las flechas grandes • Alignez les grandes flèches • Alignez les grandes flèches •...
- Page 9 All manuals and user guides at all-guides.com RJ45 24VAC POWER Camera Max 40 Watts Camera Orange Heater/Blower Yellow 26 Watts Heater/Blower Green Alarm 1 Blue Alarm 2 Violet Alarm 3 Gray Common White Make the appropriate male and female connections. Indoor model does not include pre-run cables. •...
- Page 10 All manuals and user guides at all-guides.com Axis 213 (3) #8x3/8” Captive Screw Mounting Plate 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Page 11 All manuals and user guides at all-guides.com Axis 215 (3) #8x3/8” Mounting Plate ½" 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate using (4) #8 bolts and star washers. Place (3) #8x3/8” screws on the spacers and line up the mounting slots. Slide plate in and secure. •...
- Page 12 All manuals and user guides at all-guides.com Connection Module Screw Power Board To remove the power board, use screwdriver to release plastic fasteners by applying pressure to sides while pulling out. This is what the typical path of illumination will look like with the setting at 30 degrees. Attach connection module as shown.
- Page 13 All manuals and user guides at all-guides.com Axis 233D Remove power board located inside of housing and then remove mounting bracket. • Quite a tablero de energía situado dentro de la cubierta y después quite el soporte de montaje. • Enlevez carte d'alimentation situé à l'intérieur de du logement et puis enlevez le support. •...
- Page 14 All manuals and user guides at all-guides.com Acti 8201 Captive (4) #8x3/8” Screw Mounting Plate ½" 1" 2" MOUNTING HOLE Attach camera bracket to mounting plate using (1) ¼” x 20 bolt, washer and lock washer. Complete assembly as shown, securing camera and mounting plate to spacers. •...
- Page 15 All manuals and user guides at all-guides.com CANON - VB-C10 Captive Screw Mounting Plate (3) #8x3/8” 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Page 16 All manuals and user guides at all-guides.com ELMO 400/401 Captive (4) #8x3/8” Screw Mounting Plate ½" 1" 2" MOUNTING HOLE MOUNTING HOLE Attach camera to mounting plate using (4) #8 screws, star washer, and nuts. Complete assembly as shown, then secure camera and mounting plate to spacers. •...
- Page 17 All manuals and user guides at all-guides.com JVC-VN625U Captive (4) #8x3/8” Screw Mounting Plate 1" MOUNTING HOLE Attach quick release bracket to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 18 All manuals and user guides at all-guides.com Panasonic KX-HCM180 Captive (3) #8x3/8” Screw Mounting Plate 1" 2" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, lock washer, and washer. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 19 All manuals and user guides at all-guides.com Panasonic WV-NS954 (4) #8x3/8” Mounting Plate ½" MOUNTING HOLE Attach bracket to (4) spacers using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 20 All manuals and user guides at all-guides.com Sony RZ25 Captive (3) #8x3/8” Screw Mounting Plate ½" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, washer, lockwasher, (2) M3 x 8mm bolts, and lockwashers. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 21 All manuals and user guides at all-guides.com Sony RZ50 Captive (3) #8x3/8” Screw Mounting Plate 2" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, washer, lock washer, and (2) M3 bolts and washers. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 22 All manuals and user guides at all-guides.com TOSHIBA Captive (3) #8x3/8” Screw Mounting Plate 1" 2" MOUNTING HOLE Attach camera to mounting plate using (4) #8 screws, star washer, and nuts. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 23 All manuals and user guides at all-guides.com Before After Loop the lanyard around the tab inside the Align the arrows on the outside of the dome housing. and lock. • Alinee las flechas en el exterior de la bóveda y •...
- Page 24 All manuals and user guides at all-guides.com PB24 Addendum Additional wires are provided to run power to PB24. Use with connector supplied. Run RJ45 connector through PB24, wall mount, and connect lead from housing. • Los alambres adicionales se proporcionan a la energía funcionada con a PB24. El uso con el conectador proveyó. Funcione con el conectador RJ45 con PB24, emparede el montaje, y conecte el plomo de la cubierta.
- Page 25 All manuals and user guides at all-guides.com Replacement Parts List FDW75 PART NUMBER DESCRIPTION FD7C CLEAR REPLACEMENT CAPSULE 1A FD7T TINTED REPLACEMENT CAPSULE RPFD7501 LOWER TRIM RING RPFD703 DOME CLAMPING RING RPNET02 NETWORK HGS POWER SUPPLY RPFD072 24V HEATER 5A RPFD072/12...
- Page 26 All manuals and user guides at all-guides.com Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry. Should a problem arise, rest assure that Videolarm stands behind its products by offering some of the most impressive warranty plans available: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on...