Worx WU600 Manuel D'utilisation page 9

OPERATING INSTRUCTIONS
1. INSERT THE ROUTER BIT
Router Bit Selection
Depending on processing and application,
router bits are available in many different
designs and qualities:
Router bits made of high-speed steel
(HSS) is suitable for the machining of soft
materials, e. g. softwood and plastic.
Carbide tipped router bits (HM) is
particularly suitable for hard and abrasive
materials, e. g. hard wood and aluminum.
Use only routing tools with an
allowable speed matching at
least the highest no load speed of the
machine. The shank diameter of the
router bit must correspond with the
rated diameter of the collet.
Inserting Router Bits (See A)
Before any work on the machine
itself, disconnect the mains plug. It is
recommended to wear protective gloves
when inserting or replacing router bits.
Press spindle lock button (14) and keep
depressed. If required, turn the spindle by
hand until the lock engages.
Press the spindle lock button only when at a
standstill.
Insert router bit.The shank of the router
bit must be inserted at least 20 mm (shank
length).
Tighten the tightening nut (13) with the
spanner (19) (size 22 mm). Release the spindle
lock button.
Do not tighten the tightening nut
of the collet without a router bit
inserted.
2. MOUNTING THE EXTRACTION
ADAPTER (See B)
To connect the vacuum cleaner via a suction
hose, you must fasten dust adapter (20) to
base plate (10) with both knurled screws (25).
When mounting the extraction
adapter, ensure correct mounting
position!
• For dust extraction, the vacuum hose can
be connected directly to the extraction
adapter.
• Clean the dust adapter (20) regularly to
ensure optimum dust extraction at all
times.
• The vacuum cleaner must be suitable for
the material to be worked.
• When vacuuming dry dust that is especially
detrimental to health or carcinogenic, use a
special vacuum cleaner.
Router
13L-WU600 WU600.1 WU601 WU601.1-M-070305¸ÄFÓïCE´¦.indd 9
All manuals and user guides at all-guides.com
3. ON AND OFF SWITCH
For starting the machine, actuate the lock-off
button (16) first, and then press and hold the
On/Off switch (18) afterwards.
Speed Pre-selection
The required speed can be pre-selected with
the thumb-wheel (17) (also whilst running).
1 – 2 = low speed
3 – 4 = medium speed
5 – 6 = high speed
The required speed is dependent on the
material and can be determined by practical
testing.
After longer periods of working at low speed,
allow the machine to cool down by running it
for approx. 3 minutes at maximum speed with
no load.
Speed Table
Material Router bit-Ø Speed stages
Hardwood 4 – 10mm
(Beech)
12 – 20mm
22 – 40mm
Softwood 4 – 10mm
(Pine)
12 – 20mm
22 – 40mm
Particle 4 – 10mm
board
12 – 20mm
22 – 40mm
Plastic 4 – 15mm
16 – 40mm
Aluminum 4 – 15mm
16 – 40mm
The values shown in the chart are standard
values.The necessary speed depends on the
material and the operating conditions, and can
be determined by practical testing.
Constant Electronic Control and Soft
Start (Only for WU601&WU601.1)
Constant electronic control maintains the
speed constant at no-load and under most
working conditions. Soft start delays the
increase in motor speed to reduce the motor
"kick" or torque effect to improve operator
comfort and safety.
5-6
3-4
1-2
5-6
09
3-6
1-3
3-6
2-4
1-3
2-3
1-2
1-2
1
ENG
3/5/2007 4:29:26 PM