Publicité
Les langues disponibles
Les langues disponibles
Connecting the cabinet
•
Before connecting the cabinet, check whether the voltage
indicated on the cabinet corresponds to the voltage of your
wiring. It is essential that you should connect the cabinet to
an earthen power point. Make sure that the cable does not
stay coiled. If the cable is not long enough, it should be re-
placed by a skilled person (see 7.4). Do not use an extension
or adapter cable.
•
The cabinet must be placed in such way that the plug is vis-
ible.
Control
Starting
•
If the cabinet has been transported horizontally, it should be
left to rest for at least an hour before being connected.
•
Put the cabinet in place while leaving a space of 3 to 5 cm
between the cabinet and any other furniture or wall, so that
there is a natural air flow, and in a spot where the surround-
ing temperature is between +16 ºC and +32 ºC.
•
Connect to a power point, push the ON/OFF button and
leave the cabinet working for 2 to 3 hours, so as to make
sure that it is operating normally.
•
Maximum Hygrometry 75%
N.B: Before being connected, the cabinet must be cleaned with
a detergent for washing dishes; do not use corrosive products
or soap. Then dry carefully. To carry out this operation is obliga-
tory to switch off the equipment by removing the plug from the
outlet.
Operation
Cabinet operation is totally controlled by the thermostat, for se-
lecting the temperature inside the cabinet and control the work
of lamp.
•
Cabinet operations are controlled by a thermostat for select-
ing the temperature inside the cabinet.
•
Plug the cabinet to the current.
•
If the information in the display shows "OFF", press the ON/
OFF switch for 3 seconds.
•
Wait about 3 minutes before the compressor starts after con-
necting the cabinet.
•
To disconnect, push off the main switch ON/OFF(the display
will show "OFF") or simply unplug the cabinet.
•
Wait 10 minutes before reconnecting the cabinet.
•
Load the cabinet in such a way that the products are care-
fully stocked.
•
The digital thermostat allows adjusting the temperature
from + 1ºC to + 10ºC in the positive models and – 10ºC to –
22ºC in the negative models
•
The thermostat is factory locked, only permits to adjust the
desired temperature (set point).
•
To program the desired temperature, press ON/OFF + ▲ or
▼ buttons.
•
To lock the keyboard again proceed as stated above and
select "YES" in the "LOC" function.
•
The display will indicate the temperature of the cabinet.
•
N.B.: The differential has been regulated at 3ºC in the plant.
•
When loading the cabinet in its totality it is possible that
the alarm begins to ring after 2 hours if the cabinet has not
reached yet the programmed temperature. Push any button
to turn off the buzzer and await 12 hours for stabilization of
the temperature. In case the programmed temperature has
not been reached in this space of time, contact our technical
services.
Defrosting
•
On these models, the defrosting is manual.
•
Unplug the cabinet.
•
Remove the outlet stopper; place a container underneath
and wait for the ice to thaw. (DO NOT USE HOT WATER)
Operating messages
Message
E0
E1
LO
HI
DF
OFF
The manufacturer isn't responsible for damage caused by instal-
lation or connection errors
Maintenance
Keep the cabinet clean and avoid dust or other materials accumu-
lating in the ventilation grilles.
The maintenance operations must be done by the manufacturer,
its service agent or similarly qualified persons in order to avoid
hazard.
Replacing the lights
(models with glass door)
Led strip. The power of the illumination is 17 W/m. Power 12
V DC.
The replacing operations should be done by the manufacturer,
its service agent or similarly qualified persons in order to avoid
hazard.
8
Description
Faulty ambient sensor
Faulty defrosting sensor
Low temperature alarm
High temperature alarm
Defrost
Standby
Publicité
