Publicité
Les langues disponibles
Les langues disponibles
FIG. 1
C
F
I
G
N
H
FIG. 3
J
L
K
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may pro -
mote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory pro -
tection appropriate for the dust exposure. Direct particles away from face and body.
CAUTION: Use extra care when working into a corner because a sudden, sharp move -
ment of the cut-off tool may be experienced when the wheel or other accessory contacts a
secondary surface or a surface edge.
CAUTION: Wear appropriate personal hearing protection during use. Under some
conditions and duration of use, noise from this product may contribute to hearing loss.
COMPONENTS (Fig. 1)
A . Paddle Switch
F. 6" Cutting Wheel
B . L o c k - O ff Lever
G . Anti-Lockup Backing Flange
C . Spindle Lock Button
H . Threaded Clamp Nut
D . Spindle (not shown)
I . G u a r d
E . Side Handle
ASSEMBLY
Attaching Side Handle (Fig. 1)
The side handle (E) can be fitted to either side of the gear case in the threaded holes, as
shown. Before using the tool, check that the handle is tightened securely.
OPERATION
Guards and Flanges
It is important to choose the correct guards and flanges to use with the cut-off tool accessories.
See Figure 2 for the correct accessories.
CAUTION: Accessories must be rated for at least the speed recommended on the tool
warning label. Wheels and other accessories running over rated accessory speed may fly
apart and cause injury. Every unthreaded accessory must have a 7/8" arbor hole. If it does not,
it may have been designed for a circular saw. Use only the accessories shown in Figure 2.
Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.
Mounting and Using Cutting Wheels (Type 1)
Cutting wheels include diamond wheels and abrasive discs. Abrasive cutting wheels for metal
and concrete use are available. Diamond cutting wheels for concrete cutting can also be used.
WARNING: A 4-1/2" closed, 2-sided cutting wheel guard is not included with this tool but is
required when using 4-1/2" cutting wheels. Failure to use proper flange and guard can result
in injury resulting from wheel breakage and wheel contact. See Figure 2 for more information.
MOUNTING GUARD (FIG. 3, 4)
CAUTION: Turn off and unplug the tool before making any adjustments or remov -
ing/installing attachments or accessories.
1 . Open the guard latch (J), and align the arrow (K) on the guard with the arrow (L) on the
hub. This will align the lugs with slots on the gear case cover. Position the guard facing
b a c k w a r d .
2 . Push the guard down until the guard lug engages and rotates freely in the groove on the
gear case hub.
3 . Rotate guard (I) into desired working position. The guard body should be positioned
between the spindle and the operator to provide maximum operator protection.
4 . Close the guard latch to secure the guard on the gear case cover. You should be unable
to rotate the guard by hand when the latch is in closed position. Do not operate grinder
with a loose guard or clamp lever in open position.
5 . To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned
and pull up on the guard.
N O T E : The guard is pre-adjusted to the diameter of the gear case hub at the factory. If, after
a period of time, the guard becomes loose, tighten the adjusting screw (M) with the clamp lever
in the closed position (Fig. 5).
CAUTION: Do not tighten adjusting screw with clamp lever in open position. Undetectable
damage to guard or mounting hub may result.
MOUNTING CUTTING WHEELS
CAUTION: Turn off and unplug the tool before making any adjustments or removing
/installing attachments or accessories.
C A U T I O N : Matching diameter threaded backing flange and clamp nut (included with tool)
must be used.
1 . Place the anti-lockup backing flange on spindle with the pilot (N) facing up. Be sure the
backing flange recess is seated onto the flats of the spindle before placing wheel. The pilot
(N) on the backing flange will be against the wheel when the wheel is installed.
2 . Place the wheel on the backing flange, centering the wheel on the pilot.
3 . Install the threaded clamp nut with the pilot facing away from the wheel.
4 . Depress the spindle lock button and tighten clamp nut with a wrench.
5 . To remove the wheel, grasp the wheel and turn while depressing the spindle lock button.
WA R N I N G : When wheel is tightened, always make sure the clamp nut has rotated at least
1-1/2 turns to ensure proper thread engagement. Failure to do so could result in wheel dis -
mount and may result in injury.
A
B
E
FIG. 4
I
4-1/2" Cutting Wheels
FIG. 2
Meules à tronçonner de 114 mm (4-1/2 po.)
Disco de corte de 114 mm (4-1/2 pulg.)
Type 1 guard
protège-lame de type 1
Protector Tipo 1
backing flange
bride de soutien
pestaña de respaldo
abrasive cutting wheel
meule abrasive
disco de corte abrasivo
clamp nut
écrou de blocage
tuerca de fijación
FIG. 5
FIG. 6
M
SWITCH
C A U T I O N : Hold the side handle and body of the tool firmly to maintain control of the tool at
start up and during use and until the wheel stops rotating. Make sure the wheel has come to
a complete stop before laying the tool down.
PADDLE SWITCH (FIG. 6)
To turn the tool on, push the lock-off lever (B) toward the back of the tool, then depress the
paddle switch (A). The tool will run while the switch is depressed. Turn the tool off by releas-
ing the paddle switch.
WA R N I N G: Do not disable the lock-off lever. If the lock-off lever is disabled, the tool may
start unexpectedly when it is laid down.
C A U T I O N : Allow the tool to reach full speed before touching tool to the work surface. Lift
the tool from the work surface before turning the tool off.
SPINDLE LOCK
The spindle lock pin is provided to prevent the spindle from rotating when installing or remov-
ing wheels. Operate the spindle lock pin only when the tool is turned off, unplugged from the
power supply, and has come to a complete stop. Do not engage the spindle lock while the tool
is operating because damage to the tool will result. To engage the lock, depress the spindle
lock button and rotate the spindle until you are unable to rotate the spindle further.
USING CUTTING WHEELS (FIG. 7)
WA R N I N G : Do not use cutting wheels for surface grinding applications because these
wheels are not designed for side pressures encountered with surface grinding. Wheel break -
age and injury may result.
1 . Allow tool to reach full speed before touching tool to work surface.
2 . Apply minimum pressure to work surface, allowing tool to operate at high speed. Cutting
rate is greatest when the tool operates at high speed.
3. Once a cut is begun and a notch is established in the workpiece, do not change the
angle of the cut. Changing the angle will cause the wheel to bend and may cause wheel
breakage.
4 . Remove the tool from work surface before turning tool off. Allow the tool to stop rotating
before setting it down.
MAINTENANCE
Cleaning
WARNING: Blow dust and grit out of the motor housing regularly using clean, dry com -
pressed air. Dust and grit containing metal particles often accumulate on interior surfaces and
could create an electrical shock hazard if not frequently cleaned out. A LWAYS WEAR SAFET Y
G L A S S E S .
WA R N I N G : Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. Use a clean, dry cloth only.
Lubrication
D
WA LT tools are properly lubricated at the factory and are ready for use.
E
Motor Brushes
When brushes become worn, the tool will automatically stop and prevent damage to the motor.
Brush replacement should be performed by a D
qualified service personnel.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should
be performed by authorized service centers or other qualified service personnel. Always use
identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center. If you need assistance in locating any accessory for your
tool, contact: D
WA LT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286.
E
WARNING: The use of any other accessory not recommended for use with this tool could
be hazardous.
Three Year Limited Warranty
D
WA LT will repair, without charge, any defects due to faulty materials or workmanship for
E
three years from the date of purchase. For warranty repair information, call 1-800-4-D
This warranty does not apply to accessories or damage caused where repairs have been
made or attempted by others. This warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
D
WA LT will maintain the tool and replace worn parts caused by normal use, for free, any time
E
during the first year after purchase.
If you are not completely satisfied with the performance of your D
or Nailer for any reason, you can return it within 90 days from the date of purchase with a
receipt for a full refund – no questions asked.
FREE WARNING LABEL R E P L A C E M E N T: If your warning labels become illegible or are
missing, call 1-800-4-D
Type 1 guard
protège-lame de type 1
Protector Tipo 1
backing flange
bride de soutien
pestaña de respaldo
diamond cutting wheel
meule diamant
disco de corte de diamante
clamp nut
écrou de blocage
tuerca de fijación
FIG. 7
A
B
WA LT authorized service center or other
E
WA LT tools are covered by our:
E
1 YEAR FREE SERV I C E
90 DAY M O N E Y BACK GUARANTEE
WA LT for a free replacement.
E
6" Cutting Wheels
Meules à tronçonner
de 152 mm (6 po.)
Disco de corte
de 152 mm (6 pulg.)
Type 1 guard
protège-lame de type 1
Protector Tipo 1
backing flange
bride de soutien
pestaña de respaldo
abrasive cutting wheel
meule abrasive
disco de corte abrasivo
clamp nut
écrou de blocage
tuerca de fijación
WA LT.
E
WA LT Power Tool, Laser,
E
Publicité
